Installing a High Flow Fuel Sending Unit

If you’ve ever buried your foot to the floor on the drag strip, and run into a stumble, there’s something that becomes clear in a big hurry: Getting the fuel from the tank to the carb is rather important.  If you don’t have sufficient fuel, then the ET slip will certainly reflect it.  In fact, in some vintage cars, fuel delivery is so poor, you can actually feel the deficiency as you wind through the gears.  A big part of the puzzle for any car is to supply a sufficient volume of gasoline.  Now you might think this is all very simple.  The reality is, it’s not – especially if you want to get it done with a lone stock style mechanical fuel pump.   This article is all about the importance of having the right fuel sending unit for your setup.

Ponder this: You’re kicking back a good old-fashioned milkshake.  Instead of using that big fat straw the shake normally comes with, substitute it for the itsy-bitsy straw you’d normally use with a soda pop.  You’ll soon discover that sucking that mouthful of shake isn’t exactly easy.  Replace that soda pop straw with a big milk shake straw and it’s pretty comfortable.  The same applies to a fuel system.  That’s why some performance cars from the musclecar-era were factory-fitted with larger than standard diameter fuel lines (for example, a 3/8-inch line instead of a more common 5/16-inch or smaller jobs).  The problem is, the big bottleneck isn’t right at the fuel line.  It begins way before that with the sending unit.

The fuel sender is absolutely critical.  A big restriction in a production line fuel delivery system is the fuel tank pickup/sending unit combination.  If you’re building a high flow arrangement, you have two choices: Try to find a 3/8-inch replacement pickup and sending unit (these were used on select big engine muslcecars and in some cases, they’re not exactly easy to find) or copy what plenty of F.A.S.T. guys do: Replace the factory sender/pickup with a custom billet job from the folks at RobbMc Performance Products.  The RobbMc setup is based upon a huge ½-inch diameter pickup and it does away with the troublesome sock filter the OEM replacements come with.  The dilemma with the sock is that it can become plugged and you don’t know it.  Fuel flow goes down and, obviously, so does performance.  The custom pickup requires an external fuel filter (not a bad idea for any car), but otherwise bolts into place as stock.  It’s a slick piece and if you’re searching for maximum fuel flow from a stock gas tank, this is the place to begin.

Now RobbMc doesn’t just offer one style of sender.  They have several different versions for a wide array of vintage iron.  You can order it with a conventional

½-inch tube outlet/return or you can specify -8AN or even -10AN outlet and return lines.  Case-in-point is the setup shown in the accompanying photos. It’s designed for a first generation Camaro (or 1968-74 Nova or other GM X-body).  And as you can see, it comes equipped with -8AN male fittings on both the feed and return lines. In our case, we didn’t need a return, so it was simply capped. It’s all very cool and extremely well built.

The bottom line here is, these trick senders/fuel pickups end fuel starvation right at the source. They’re not even that expensive.  The RobbMc ( piece shown here costs $149.00 plus an additional $20.00 for the -8AN package.  For a closer look, check out the accompanying photos:

high flow fuel sending unit
Instead of trying to make a factory sender work, check out this option: This is a billet ½-inch pickup offered by RobbMc Performance. As you can see in this photo, there is no provision for fuel filter sock. More in the next photo:

high flow fuel sending unit

high flow fuel sending unit
The RobbMc pickup is simply wide open inside the tank. The pickup measures ½-inch. As pointed out in the text, you have to add an in-line fuel filter. RobbMc makes similar pickups for a wide cross section of vintage applications.
high flow fuel sending unit
The float is a high quality piece. Ditto with the actual sending unit, which by the way is designed to work with the stock production line fuel level gauge.
high flow fuel sending unit
On the topside, the RobbMc pickup is engineered for use with return line, if needed. If you don’t need one (as in our application), simply use an AN cap to plug the extra line (ours came with the return line pre-capped). The actual feed line is also equipped with an -8AN male outlet (a $20 option).
high flow fuel sending unit
Here’s a look at the RobbMc pickup installed in the tank. Installation is a breeze. Simply drop the supplied O-ring into the tank bung, line up the pickup and tighten the lock ring. Simple. As far as wiring for the gas gauge is concerned, the black wire is the ground. The positive red wire goes to the factory wiring harness connector.
high flow fuel sending unit
With the tank installed, here’s how the feed and return lines look. As you can see plumbing becomes simple with a capital “S”. We dig this setup – a lot!

Be the first to comment

Leave a Reply

Your email address will not be published.


I agree to receive emails from I understand that I can unsubscribe at any time. Privacy Policy
Copyright © 2005-2021 MH Sub I, LLC dba Internet Brands
All Rights Reserved.

Internet Brands