Carb Problem

Old 12-18-2012, 04:36 PM
  #1  
gullion454
Member
MASTER JOURNEYMAN
Thread Starter
 
Join Date: May 2003
Posts: 35
Default Carb Problem

I have a Speed Demon, #1402010, which is suppose to be a 750 cfm. When I put it on my street 454 and it seemed to drown it with fuel. I then switched to a Holley 650 cfm and it runs better. But I thought I'd get more power with the 750. Any suggestions? Here is my engine run down:

454 block
forged pistons - 10.75:1 compression
new chromoly rings
cam - .544 lift
roller rockers
rebuilt open chambered heads
Weiand aluminum intake
Mallory distributor
Stock mechanical fuel pump
gullion454 is offline  
Old 12-18-2012, 07:02 PM
  #2  
TS1955
Senior Member
DYNO OPERATOR
 
Join Date: Aug 2007
Location: Lost Creek, WV
Posts: 533
Default

There are a few things to look for. Since is seems to run ok with the 650 you fuel preesure should be alright. Check your float level. Then make sure your jetting is in the ball park for that carb. Do some research to find out the factory jetting should be. That will be a good starting point. Then check your power valve(s). They could be ruptured or wrong for your application.

TS1955
TS1955 is offline  
Old 12-21-2012, 05:48 AM
  #3  
outlaw256
Senior Member
RACING JUNKIE
 
Join Date: Mar 2008
Location: falkville al
Posts: 1,766
Default

id be lookin at that 750 carb.like float level for starters.that engine should be able to handle 750.
outlaw256 is offline  
Old 12-22-2012, 07:10 AM
  #4  
coloradoracerguy
Senior Member
SENIOR BUILDER
 
Join Date: Dec 2007
Location: Morrison, Colorado
Posts: 120
Default

A larger carb doesn't always mean more power. Lots of things to consider. The biggest thing is calibration. It's got to be right for the motor it's on or it won't make a difference at all, and can even lose power. I'd take that carb completely apart and blow out all the passages, make sure there's no debris in it at all. Put it back together and set the floats with the level at the bottom of the sight glasses to start, and see how it does from there. What jetting, air bleeds, etc are in the carb? Did you get it used or new?
coloradoracerguy is offline  
Old 12-29-2012, 11:20 AM
  #5  
bixblk
Senior Member
DYNO OPERATOR
 
bixblk's Avatar
 
Join Date: Dec 2004
Location: Chicagoland area
Posts: 472
Default carb

That motor should like a 750 cfm carb.
All the above info /tips I agree with.
I have put 850 CFM DP holleys on 454's with similar parts, and it was fine.
You probably have a carb issue with the 750
Good Luck
bixblk is offline  
Old 01-01-2013, 10:15 AM
  #6  
gullion454
Member
MASTER JOURNEYMAN
Thread Starter
 
Join Date: May 2003
Posts: 35
Default

thanks guys.
gullion454 is offline  
Old 01-08-2013, 09:00 PM
  #7  
chevyart
Senior Member
MASTER BUILDER
 
Join Date: Mar 2008
Posts: 173
Default 750 carb

that holley 750 out of factory should have 75 front and 75 rear jets with a 6.5 power valve in both front and rear. no power valve in rear, then step rear jets up to around 82(and try 84s). you may have to step up the timing at idle to get the carb to idle properly(and remove some timing from the full advance position) art
chevyart is offline  
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service