BLOWERS W/injection

Old 03-14-2012, 05:59 PM
  #1  
injectedrat68
Junior Member
APPRENTICE
Thread Starter
 
Join Date: May 2003
Location: Broad Brook,CT.
Posts: 23
Default BLOWERS W/injection

I know they say you should run low compression with a blower @ 8.5 i think. My question is can i still run a blower with a big and ugly injection hat with a compression of about 12.1 on alka. My car is a full tube chassis, hopefully with a cert. 8.50 Just trying to figure out which engine combos to go with. ( (blowers w/ injection or tunnel ram injection) Thanks for responding Paul
injectedrat68 is offline  
Old 03-14-2012, 07:26 PM
  #2  
zipper06
Senior Member
RACING JUNKIE
 
Join Date: Jan 2006
Location: La.
Posts: 2,890
Default

Absolutely, i've ran 13.5/14.0 to one with a B/BLK 540 running 40% overdrive with a buzzard catcher. Engine ran [email protected] in 1985 in Linda Lanes top alcohol car.
I've got a 358" (broke now) with 12.0 and 1471 Littlefield with buzzard catcherat 30% OD ( the block gave up) it was stock 350 010 hi nickel blk filled to the top. It's going back together with a Dart blk 383" and i'll be running the same combo. It went 4.62 in the 1/8 with the 358" I luv blowers and alcohol (in that order :lol: )


Zip.
zipper06 is offline  
Old 03-16-2012, 04:33 PM
  #3  
injectedrat68
Junior Member
APPRENTICE
Thread Starter
 
Join Date: May 2003
Location: Broad Brook,CT.
Posts: 23
Default blowers

Hey zip how it going, anyway i talked to an shop up in MN who advertise blower built motors. They told me i can run 12.5/1 and it would have to be on alka. Ok sounds good. Now- i called another blower builder down in TX. He told me i couldnt run that compression over or under drive cause it blow the bottom right out. Also recommed that i have a 4 bolt . They also said the inside of the blower had to have a special coating on it because the alka would melt the alum. I thought alka runs really cold ? So i think im back to square one on what to do. I still havent finished putting the ft. clip on the camaro yet. Been freaking wicked busy, i guess thats good for others but i think im going to get a late start this yr. again. Thanks for reading the letter Paul
injectedrat68 is offline  
Old 03-16-2012, 06:59 PM
  #4  
zipper06
Senior Member
RACING JUNKIE
 
Join Date: Jan 2006
Location: La.
Posts: 2,890
Default Re: blowers

Originally Posted by injectedrat68
Hey zip how it going, anyway i talked to an shop up in MN who advertise blower built motors. They told me i can run 12.5/1 and it would have to be on alka. Ok sounds good. Now- i called another blower builder down in TX. He told me i couldnt run that compression over or under drive cause it blow the bottom right out. Also recommed that i have a 4 bolt . They also said the inside of the blower had to have a special coating on it because the alka would melt the alum. I thought alka runs really cold ? So i think im back to square one on what to do. I still havent finished putting the ft. clip on the camaro yet. Been freaking wicked busy, i guess thats good for others but i think im going to get a late start this yr. again. Thanks for reading the letter Paul
Paul, both people are right. You didn't say SM/BLK or B/BLK, but you have to have a good after market block and a good rotating assy with blower pistons, to run that compression also in all cases you can't run a street blower, it has to be hard anidized, the case and the rotors and with tefloned rotors inserts (IE racing blower) I broke mine because it was stock 350 4 bolt hi nickle blk, i was making perhaps 1200 HP, the block just couldn't handle it.

Zip.
zipper06 is offline  
Old 03-17-2012, 03:29 AM
  #5  
injectedrat68
Junior Member
APPRENTICE
Thread Starter
 
Join Date: May 2003
Location: Broad Brook,CT.
Posts: 23
Default blowers

Alright then that settles that. I guess ill stay with what i have this yr. and sell the motor this fall unless i dont get to race at all this yr.Let me ask you this, is it possible to spend somewhere of 10k or less for a decent blower motor. Thats kind of what i have to spend. Ill talked to ya later, i got to go to my class this morning 7am- 3pm have a good day. Paul
injectedrat68 is offline  
Old 03-20-2012, 01:15 PM
  #6  
A65rocketman
Junior Member
SHOW GUEST
 
Join Date: Jan 2010
Posts: 7
Default Sheet metal manifold with alky, nos injectors

I might have something you'd be interested in, can email pic's to a personal email only.

Thx. Jerry, 65rocketman.live.com or 352 357 4248
A65rocketman is offline  
Old 03-24-2012, 02:54 AM
  #7  
injectedrat68
Junior Member
APPRENTICE
Thread Starter
 
Join Date: May 2003
Location: Broad Brook,CT.
Posts: 23
Default post subject

A65rocketman i sent you a pm with my E-mail.
injectedrat68 is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service