Estimated HP/Torque?

Old 07-17-2011, 04:58 PM
  #1  
chevlrag69
Junior Member
SHOW GUEST
Thread Starter
 
Join Date: Apr 2009
Posts: 7
Default Estimated HP/Torque?

Combo is standard bore 350cid.Older style B&M 142 blower (restripped/bearings etc).Dart Pro 1,s 200 cc intake runners,(2.02x1.60) (unported) but matched to blower intake.Camshaft is Comp special order,ADV DUR.intake 274,exhaust [email protected] .050 is 224 intake/230 exhaust.Valve lift.is,intake .538,exhaust .534. Lobe sep is 115. This is a hydralic roller.Also running comp ultra gold 1.6 roller rockers to up the lift to roughly .565/.560.or thereabout.750 cfm holley.I,m thinking or hoping that this combo will be a torquey little small block.It ran 11.60 @115 with .435"/.460"/212/222 duration flat tappet cam in 69 camaro @ 3470#. How much torque and horsepower should I pick up changing to a roller setup.Thanks
chevlrag69 is offline  
Old 07-18-2011, 11:08 AM
  #2  
bluedawg357
Member
CRAFTSMAN
 
Join Date: Dec 2010
Location: anchorage alaska
Posts: 56
Default

I dont now what the gains will be, but it sure dose sound fun.
bluedawg357 is offline  
Old 07-18-2011, 03:22 PM
  #3  
bixblk
Senior Member
DYNO OPERATOR
 
bixblk's Avatar
 
Join Date: Dec 2004
Location: Chicagoland area
Posts: 472
Default cam change

Alot of guys on here have more experience with cam shafts , but in general a roller should help HP because of its design, rise fall times which also can help cam indexing timing and durations. That being said they can be a little more expensive and harder on the valve train. I would be quessing at the HP gain, the proper overall combo is as important or possibly more important than the actual type of cam, but generally roller will help if you have the cash to buy them.JMO
bixblk is offline  
Old 07-24-2011, 12:24 AM
  #4  
chevlrag69
Junior Member
SHOW GUEST
Thread Starter
 
Join Date: Apr 2009
Posts: 7
Default

Appriciate the input..I think it made roughly 400hp with flat tappet (small cam shaft).You need 400 hp to run 11.60,s @3400#.Hoping for an additional 65 to 70 HP. Any thoughts as to get me in the 10,s Thanks. 8)
chevlrag69 is offline  
Old 07-24-2011, 06:11 AM
  #5  
lsrholder
Member
JOURNEYMAN
 
Join Date: Nov 2006
Posts: 31
Default

Have you tried /borrowed say an 830-850 cfm carb ?

Changed the blower drive ratio for a "bit" more psi ?

Nice easy spots to try, much less labor and $$$ intensive.

Have E-85 available locally, is another thought, and with a blower sure keeps detonation down.
lsrholder is offline  
Old 07-31-2011, 02:40 AM
  #6  
chevlrag69
Junior Member
SHOW GUEST
Thread Starter
 
Join Date: Apr 2009
Posts: 7
Default

Had 800 on there,Everyting fell off. ET.etc Of course that was before supercharger restrip.Gotta get new cam and roller cam installed and see what this motor makes? Hopefully 6/7 psi,i,m thinking? Any Thoughts?
chevlrag69 is offline  
Old 08-02-2011, 06:26 PM
  #7  
DogGear
Junior Member
SHOW GUEST
 
Join Date: Jun 2011
Posts: 5
Default

Hi rags
How much boost at what RPM? I bet boost will drop at a non desirable low rpm.
DogGear is offline  
Old 08-03-2011, 10:25 AM
  #8  
maxpower671
Senior Member
SENIOR BUILDER
 
Join Date: Dec 2005
Posts: 117
Default

don't get too caught up in the boost "number"....lots of things affect that....after all that is a measure of restriction too....
maxpower671 is offline  
Old 08-06-2011, 09:20 PM
  #9  
chevlrag69
Junior Member
SHOW GUEST
Thread Starter
 
Join Date: Apr 2009
Posts: 7
Default

I totally agree.Heads,cam etc.Was just looking for thoughts on HP/torque that this combo will make? Thanks.Sorry no E85 available in Canada,yet at pumps.Only get (Contains 10% ethanol).Also would have to change carb, fuel line,and use all anodized fittings,etc.Little to much hassel at this time.Very good article on E85 in Oct/2011 issue. E85 versus 112 gas.If I,m not mistaken,can,t run ethanol with stripped blower? Needs to be just rotors for more clearance.Please correct me if I,m wrong.Thanks
chevlrag69 is offline  
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service