no start

Old 03-13-2011, 06:11 AM
  #1  
mikesramblur
Member
JOURNEYMAN
Thread Starter
 
Join Date: Jan 2008
Location: ontario, can.
Posts: 30
Default no start

Ive got a new hei ignition on an amc 360 that i seem to think might be a problem. its chev style ignition, coil in cap.
its always started and run fine. last week it decided to not start after sitting for about 4 weeks.
i checked 3 plugs and got lots o spark at these. got gas, rotor turns, cap and rotor no cracks, turns over fine, just wont catch.
could a module cause this? do these coils either work or they dont?
what about the soilioid, can they do this? (remote solenoid on fenderwall)

any help would be great. im outta ideas.

thanks
mikesramblur is offline  
Old 03-13-2011, 06:37 AM
  #2  
johnracer
Senior Member
DYNO OPERATOR
 
Join Date: Aug 2005
Location: Rifle Colorado
Posts: 585
Default

Maybe try some fresh fuel.....

Johnny
johnracer is offline  
Old 03-13-2011, 09:03 AM
  #3  
TheYellaBrick
Senior Member
RACING JUNKIE
 
TheYellaBrick's Avatar
 
Join Date: Mar 2008
Location: Emmett, Idaho
Posts: 7,334
Default

In that vein, try squirting fresh gas into the carb and see if it catches before draining and refilling the tank/system.

"Got gas", does that mean you disconnected the fuel line at the carb and turned it over ? SAFETY NOTE; DO NOT let any gas spray onto ANY ignition component while doing this !! ops: ops: ops: I got the T-shirt from THAT one ops: ops:
TheYellaBrick is offline  
Old 03-13-2011, 08:09 PM
  #4  
mikesramblur
Member
JOURNEYMAN
Thread Starter
 
Join Date: Jan 2008
Location: ontario, can.
Posts: 30
Default

:lol: nope. i didnt do that. means theres gas in the carb squirting into the ventures.
this is the fourth time today i heard that the gas is no good. ill give it a try this week.
keep ya posted.
mikesramblur is offline  
Old 03-13-2011, 08:18 PM
  #5  
bixblk
Senior Member
DYNO OPERATOR
 
bixblk's Avatar
 
Join Date: Dec 2004
Location: Chicagoland area
Posts: 472
Default motor starting

it is cracking really fast, faster than usual. I hope you did not break a timing belt or chain or gear.
Gas in the carb is a great idea, or a shot of starting fluid ,,,,, but as told above be careful
Good luck
also did you check the cap I have seen moisture and green oxidation under caps but show a spark at some plugs, maybe pull the cap and flip it over to check, just a thought
bixblk is offline  
Old 03-14-2011, 03:22 AM
  #6  
mikesramblur
Member
JOURNEYMAN
Thread Starter
 
Join Date: Jan 2008
Location: ontario, can.
Posts: 30
Default

it cranks as usual. i checked that the rotor was spinning when cranking. under cap is good.
im going to try some new gas in the carb tonite.
mikesramblur is offline  
Old 03-14-2011, 03:14 PM
  #7  
mikesramblur
Member
JOURNEYMAN
Thread Starter
 
Join Date: Jan 2008
Location: ontario, can.
Posts: 30
Default

ok i does run when squirting gas into carb. but runs very rough then stops. i just found out the primary squirter is not working. secondary works great, and thats what i was looking at before. well duhhhhh on me for not taking a closer look into the carb. also should of known something was up when the primary diaphragm was dripping out the bottom.

more operator stupidity.
thanks all for the tips.
mikesramblur is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service