recamming the SBC 406 questions

Old 07-25-2010, 05:32 AM
  #1  
rabiddawg
Senior Member
DYNO TECH
Thread Starter
 
Join Date: Aug 2007
Location: Colebrook Connecticut
Posts: 425
Default recamming the SBC 406 questions

going with an isky hydraulic roller
cam card here.
anyone use this cam ?
i got 3:93 rear ratio and 2500 stall converter on a built th350.
brodix -10 aluminum heads
11:1 compression
also I got 150 nitrous shot on the plate.
will this cam work ????
thoughts???



TIMING CHART

PART NUMBER: 211282/294GRIND NUMBER: rr-282/294ENGINE INFO: CHEVY SMALL BLOCK V8 305-350 CU.IN. 1988-UPAPPLICATION: SPECIAL REMARKS: HYDRAULIC ROLLERPRODUCT USE: STREET/STRIPRPM RANGE: 3000-7000Valve lift is calculated with zero lash and rocker ratio of 1.5INTAKE TIMING DURATION: 282deg.OPEN: 31BEFORE TDCCLOSE: 71AFTER BDCCAM LIFT: .353"VALVE LIFT: .530"VALVE LASH: .HOT.COLDEXHAUST TIMING DURATION: 294deg.OPEN: 77BEFORE BDCCLOSE: 37AFTER TDCCAM LIFT: .367"VALVE LIFT: .550"VALVE LASH: .HOT.COLD
LOBE CENTER: 110 deg.OVERLAP: 68 deg.CAM ADVANCE: 0 deg.THE ABOVE TIMING IS CHECKED AT .020(OPEN) LIFTER RISE.020(CLOSE)The following timing is taken at .050" lifter rise and gives a more accurate determination of camshaft position.INTAKE DURATION: 234deg.OPEN: 7BEFORE TDCCLOSE: 47AFTER BDCEXHAUST DURATION: 246deg.OPEN: 53BEFORE BDCCLOSE: 13AFTER TDCRECOMMENDED ISKY CAM KIT PARTS AND SETUP INFORMATION

LIFTERS: USE STOCKLIFTER TYPE: HYDRAULIC ROLLERSPRING: 6105TYPE: dual W/DAMPERDIA.: 1.430"RATE: 330 lbs per inchINSTALLED HEIGHT: 1.812"SEAT PRESSURE: 135 lbsOPEN PRESSURE: 315 lbsCOIL BIND: 1.120"SPRING SHIMS: # 2STEEL RETAINERS: 507-STATITANIUM RETAINERS: 60-TIPUSHRODS: 203-HG-.460"TYPE: heat treated non-adjLENGTH: 7.200"DIA.: 5/16"ROCKER ARMS: 204TYPE: rollerRATIO: 1.5VALVE LOCKS: VL-32VALVE LOCKS: VL-32REV KIT:

home | what's new | tech info | news | catalog | apparel | about | contact
2002 Isky Racing Cams. All rights reserved.
rabiddawg is offline  
Old 08-20-2010, 02:16 AM
  #2  
rabiddawg
Senior Member
DYNO TECH
Thread Starter
 
Join Date: Aug 2007
Location: Colebrook Connecticut
Posts: 425
Default

yeah hey thanks for the helpful advice!
rabiddawg is offline  
Old 08-20-2010, 04:18 PM
  #3  
carssteve36
Junior Member
APPRENTICE
 
Join Date: Dec 2009
Posts: 23
Default

This is the cam I used in my 69 camaro with a 406 howards cam part #110265-10 works good what ever cam you use you will need more stall converter nice car
carssteve36 is offline  
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service