Any one guess what they flow??? old set of brodix -10s

Old 04-14-2009, 04:33 PM
  #1  
cartwright454
Junior Member
JOURNEYMAN
Thread Starter
 
Join Date: Oct 2003
Posts: 28
Default Any one guess what they flow??? old set of brodix -10s

I picked up a set of old brodix -10 that have been fully ported buy rons porting service. they have 2.08 intake and 1.6 ext. , they are the spread prot exhaust. I have a set of felpro 1206 gaskets and they are a little smaller than the port. I did call rons and they were not much help. Any one have any quess what they could flow? Thanks for any help Billy C
cartwright454 is offline  
Old 04-14-2009, 09:21 PM
  #2  
radicalz
Senior Member
MASTER BUILDER
 
Join Date: Dec 2004
Location: out of my mind in Kalamazoo, MI
Posts: 179
Default

Billy call Curtis Boggs at Raceflow Development...he should be able to help ballpark them...Topsportsman has a post of him and his site at the top of the engine tech page....good man...will get you in the right direction...
radicalz is offline  
Old 04-15-2009, 06:13 AM
  #3  
zipper06
Senior Member
RACING JUNKIE
 
Join Date: Jan 2006
Location: La.
Posts: 2,890
Default

I ran an old set of Brodix 10's about 20 yrs. ago and if i recall they flowed about .285 at .600 lift. Those heads require offset int. rockers.
I now have a set of the newer Brodix 10's they are spred port EX, and Raised port intake(1277 gaskets .120 tk), with 2.140 int. I also had to make 1/4" spacers between the top of the blk. and the bottom of the int. manifold. I don't have the flow charts on them and they flowed 308 @ .600 and 314 @ .700, they are setting on my 434" that's going into my Malibu.

hope this helps.

Zip.
zipper06 is offline  
Old 04-16-2009, 03:47 AM
  #4  
cartwright454
Junior Member
JOURNEYMAN
Thread Starter
 
Join Date: Oct 2003
Posts: 28
Default

Thanks for your help. I was guessing about 300 cfm @.700. They look like rons did a very nice job but you never know untill you run them. They are going on my littl old 71 vega small tire street car with a 406, glide with brake. should be fun. thanks again Billy c
cartwright454 is offline  
Old 04-18-2009, 05:19 PM
  #5  
wrightway
Senior Member
SENIOR BUILDER
 
Join Date: Feb 2005
Location: LAWTON MI
Posts: 113
Default

Billy those heads won’t flow at all until you get a big hand full of my nuts :shock: for your rockers :lol: :lol:
wrightway is offline  
Old 04-20-2009, 05:10 PM
  #6  
cartwright454
Junior Member
JOURNEYMAN
Thread Starter
 
Join Date: Oct 2003
Posts: 28
Default

Hi Joe, I have a hand full of nuts now but I think it will take a bucket of Balls to run it. Just hopin it will run low 11's .
cartwright454 is offline  
Old 04-24-2009, 08:52 AM
  #7  
NUBBY1
Junior Member
SHOW GUEST
 
Join Date: Feb 2007
Posts: 2
Default brodix-10 rons porting

I HAVE THE SAME SET OF HEADS AND THEY FLEW 326 @ 700LIFT I THINK IF YOU WANT I CAN LOOK UP THE #.IF INTERESTED SEND ME A MESSAGE VIA RJ OR E-MAIL [email protected]
NUBBY1 is offline  
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service