Aftermarket Wiring Harnesses

Old 08-08-2007, 02:54 PM
  #1  
ssym
Member
JUNIOR BUILDER
Thread Starter
 
Join Date: Apr 2007
Location: West Palm Beach, Florida
Posts: 71
Default Aftermarket Wiring Harnesses

I am rewiring a '66 Chevy II. Although I dislike the term, it will be ProStreet, ie lights, ign, fuel, fans, etc. No radio or heat/AC. Can I get some feed back on Ron Francis and Painless. Or anything else that may be out there.

Thanks,

Steve

I read alot, this is my 1st post
ssym is offline  
Old 08-08-2007, 03:06 PM
  #2  
Robert1320
Member
JUNIOR BUILDER
 
Join Date: Jun 2006
Location: The Custom Engine Shop, Indianapolis, Indiana
Posts: 73
Default

Steve,

Check out http://www.horsepowerconnection.com/ Brian makes wiring.
Robert1320 is offline  
Old 08-09-2007, 03:24 AM
  #3  
curtisreed
Senior Member
RACING JUNKIE
 
curtisreed's Avatar
 
Join Date: Feb 2004
Location: KIEFER, OK.
Posts: 1,312
Default

Here are a couple of options. I have a Painless box in my car but I looked at these two at the IHRA national in Tulsa, they both have nice stuff.

http://www.trickcableandswitch.com/mm5/merchant.mvc

http://www.racewiring.com/

Curtis
curtisreed is offline  
Old 08-09-2007, 05:28 PM
  #4  
Racefab57
Senior Member
DYNO OPERATOR
 
Join Date: Nov 2006
Location: NC
Posts: 558
Default

I use ARC (autorod control) panel, and prostock wiring harness!!! ITS GREAT,and much cheaper than painless!!!!!!! pm me ill give you the low down! David.
Racefab57 is offline  
Old 08-11-2007, 04:25 AM
  #5  
spib
Senior Member
RACING JUNKIE
 
Join Date: Jan 2006
Location: EastWenatchee,WA
Posts: 887
Default

http://www.jegs.com/webapp/wcs/store...10002_15198_-1 I used this painless universal fuse box, and would use it again, bought some wire and relays and the jegs control panel for overhead, and have another small panel next to sterring whell for togles for lights,taillights and turn signals, going to use the painless turn signal harness and run toggle switches for that!!!
spib is offline  
Old 09-14-2007, 07:55 PM
  #6  
hotrodharley
Senior Member
EXPERT BUILDER
 
Join Date: Dec 2002
Location: spring creek nv.
Posts: 329
Default

hi;;try also look at EZWIRING..I'VE USED THERE'S IN MANY OF MY BUILDS.I LIKE THEM BETTER THEN PAINLESS MYSELF.AND CHEAPER THEN PAINLESS AND THEY HAVE SOME GOOD TECH IF YOU NEED TO ASK THEM ANYTHING.
hotrodharley is offline  
Old 09-17-2007, 01:30 AM
  #7  
ssym
Member
JUNIOR BUILDER
Thread Starter
 
Join Date: Apr 2007
Location: West Palm Beach, Florida
Posts: 71
Default

I ended up going with the Ron Francis Bare Bonz system. Good quality stuff and well organized kit. The instructions were a little bland, but after staring at it were while we got it figured out.

I like the flexibility of being able to run the wires to the fuse panel.

Steve
ssym is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service