CURRIE REAR END

Old 07-14-2007, 03:24 PM
  #1  
lively
Senior Member
RACING JUNKIE
Thread Starter
 
lively's Avatar
 
Join Date: Nov 2004
Location: ILLINOIS
Posts: 2,191
Default CURRIE REAR END

CURRIE REAR END WITH THE ALUMINUM CENTER HOUSING???[NOT THE PUMPKIN]--GOOD / BAD / OR THE UGLY?---MOSTLY STREET USE AND SOME 1/8 MILE--WHAT DO YOU THINK FOR MY RANCHERO GASSER?-LIVELY
lively is offline  
Old 07-19-2007, 03:28 PM
  #2  
zona
Junior Member
SHOW GUEST
 
Join Date: Jan 2004
Posts: 1
Default

Are you asking if its a good housing or are you selling it? :?:
zona is offline  
Old 07-19-2007, 04:19 PM
  #3  
lively
Senior Member
RACING JUNKIE
Thread Starter
 
lively's Avatar
 
Join Date: Nov 2004
Location: ILLINOIS
Posts: 2,191
Default

looking at one and wondering about the strength and limits of it 8) 8) LIVELY
lively is offline  
Old 07-19-2007, 08:42 PM
  #4  
SST4530
Senior Member
DYNO TECH
 
Join Date: Feb 2004
Location: Leonard, Texas
Posts: 414
Default

I think it would be fine for street use, but would stay away for race purposes.
SST4530 is offline  
Old 09-30-2007, 02:57 PM
  #5  
real3fann
Member
JOURNEYMAN
 
Join Date: Nov 2003
Location: SoCal
Posts: 31
Default

I have been running Currie stuff for years with no problems... 9" N section, 4.88 pro gear and 35 spline spool and there race axles NO PROBLEMS HERE WITH 1.000 HP 866 Tq Eng in a 3150LBS CAR
real3fann is offline  
Old 10-09-2007, 07:32 AM
  #6  
SST4530
Senior Member
DYNO TECH
 
Join Date: Feb 2004
Location: Leonard, Texas
Posts: 414
Default

Originally Posted by real3fann
I have been running Currie stuff for years with no problems... 9" N section, 4.88 pro gear and 35 spline spool and there race axles NO PROBLEMS HERE WITH 1.000 HP 866 Tq Eng in a 3150LBS CAR
Unless I misunderstood the question, sounds like he's talking about aluminum center with steel axle tubes? I don't think that's what your running? :?:
SST4530 is offline  
Old 10-09-2007, 09:49 PM
  #7  
real3fann
Member
JOURNEYMAN
 
Join Date: Nov 2003
Location: SoCal
Posts: 31
Default

Originally Posted by blittle
Originally Posted by real3fann
I have been running Currie stuff for years with no problems... 9" N section, 4.88 pro gear and 35 spline spool and there race axles NO PROBLEMS HERE WITH 1.000 HP 866 Tq Eng in a 3150LBS CAR
Unless I misunderstood the question, sounds like he's talking about aluminum center with steel axle tubes? I don't think that's what your running? :?:
Oh my mistake
real3fann is offline  
Old 10-12-2007, 10:14 AM
  #8  
Tod74
Senior Member
RACING JUNKIE
 
Join Date: Sep 2007
Posts: 4,143
Default

Look this guy up and have his rear end guy help you out.
http://rides.webshots.com/video/3026...01149359WVpyxw
Tod74 is offline  
Old 10-12-2007, 02:03 PM
  #9  
lively
Senior Member
RACING JUNKIE
Thread Starter
 
lively's Avatar
 
Join Date: Nov 2004
Location: ILLINOIS
Posts: 2,191
Default

HE IS LUCKY HE DIDN'T LOSE IT ON THE PASS BEFORE!!!!---THAT IS ON THE PREVIOUS VIDEO 8) 8) 8) ----THE CURRIE REAR I LOOKED AT HAD THE ALUMINUM CENTER PIECE[WAS VERY NICE LOOKING BUT I WAS NOT SURE OF THE STRENGTH]---THANKS FOR THE INFO===LIVELY
lively is offline  
Old 10-24-2007, 05:00 PM
  #10  
dragman28
Junior Member
SHOW GUEST
 
Join Date: Jul 2005
Posts: 6
Default

Hello Lively,Just thought with your inquiry about the rear axle housing I have a 9" on the classified side if interested,Thanks Dragman28.
dragman28 is offline  

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service