Anyone use a Strange Engineering 1350 driveshaft?

Old 07-09-2007, 05:24 PM
  #1  
bignastygs
Senior Member
SENIOR BUILDER
Thread Starter
 
Join Date: May 2004
Location: Loganton, Pa
Posts: 113
Default Anyone use a Strange Engineering 1350 driveshaft?

I am to the point of getting a driveshaft for my Buick and have been searching vendors for a driveshaft that has 1350 joints. I looked at Mark Williams,Dennys', and just seen the Strange shafts. I can't afford a carbon fiber one,but want a reliable unit. My car has a TH400 with reverse manual valve body and a HD built 8.5 with 1350 yoke. I'll need a complete shaft 53 inches long and with a TH 400 yoke. Has anyone had experience with the StrangeEngineering one??
bignastygs is offline  
Old 07-10-2007, 11:34 AM
  #2  
Robert1320
Member
JUNIOR BUILDER
 
Join Date: Jun 2006
Location: The Custom Engine Shop, Indianapolis, Indiana
Posts: 73
Default Inland Driveshaft

I use Moser engineering driveshafts, they are made by Inland DriveShaft.
Great product
Robert1320 is offline  
Old 07-10-2007, 03:30 PM
  #3  
Racefab57
Senior Member
DYNO OPERATOR
 
Join Date: Nov 2006
Location: NC
Posts: 558
Default

I used a DENNYS cm driveshaftw/ 1350 u joints,GREAT PIECE!! HEsgot a shaft that if you break it, he'll replace it free!!
Racefab57 is offline  
Old 07-10-2007, 04:39 PM
  #4  
bignastygs
Senior Member
SENIOR BUILDER
Thread Starter
 
Join Date: May 2004
Location: Loganton, Pa
Posts: 113
Default

I have been looking at Denny's Nitrous shafts and like them alot. I just am unsure about the aluminum one though.I know a few people on another board that use a Denny's. and they highly recommend them as well.Besides they are only about 2 1/2-3 hours from me and I could take a little drive I guess..
bignastygs is offline  
Old 07-11-2007, 01:20 PM
  #5  
Racefab57
Senior Member
DYNO OPERATOR
 
Join Date: Nov 2006
Location: NC
Posts: 558
Default

hey bignastygs, Ill meet you there if you want! Im 1.5 hr away! let me know. david.
Racefab57 is offline  
Old 07-28-2007, 07:14 PM
  #6  
bjuice
Administrator
RACING JUNKIE
 
bjuice's Avatar
 
Join Date: Apr 2003
Location: Greenville s.c.
Posts: 3,239
Default

63 vette i use the Mark Williams chrome moly shaft with the MW Billet yoke.

67 Camaro- i use a local custom made 3.5 inch mild steel 0.83 wall with the MW billet yoke.

No matter what drive shaft i choose to use I WILL always use the Billet yokes.....i have used the 1350 yokes in the past but i have saw those break in different situations ( got 2 of them in the tool box)...so i spend the extra and go with the Billet yoke.

Thanks Brian
__________________
Bjuice..

"I'M YOUR HUCKLEBERRY ! "
bjuice is offline  
Old 08-07-2007, 04:21 PM
  #7  
sg1586
Senior Member
MASTER BUILDER
 
Join Date: Dec 2003
Posts: 185
Default

Originally Posted by Racefab57
I used a DENNYS cm driveshaftw/ 1350 u joints,GREAT PIECE!! HEsgot a shaft that if you break it, he'll replace it free!!


Yep I have one of those also........Brake it and he gives you another and also free labor as long as you own it
sg1586 is offline  
Old 08-14-2007, 09:31 PM
  #8  
acpat
Junior Member
SHOW GUEST
 
Join Date: Jan 2005
Posts: 2
Default

Aluminum drive shafts require coated u-joint caps to keep them from having problems with corrosion. You can not run steel against aluminum hince the coated caps.
acpat is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service