• Texas plated, VIN stamped on frame. TX registration current through March 2027.
• Clean title, original owner.
• Only 1600 miles
• Chenowth Racing Products, Inc. Explorer
o 120” wheel base
o Fox 2.0 remote reservoir coil-overs on all four corners
o 14” front and 16” rear suspension travel
o 16” ground clearance
o Heavy duty beam style front suspension
o Foddrill 4340 link pins
o Foddrill +4” arms
o Foddrill spindles
o 3 x 3 dual pivot tubular rear trailing arms
• Engine
o Chevrolet L67 3.8L V6 fuel injected and supercharged
From 2004 Impala SS donor car, ~12,000 miles
o Very reliable, cranks up easily every time and runs super smooth, purrs at idle.
o Stock rating of: 240 hp at 5,200 280 lb-ft torque at 3600
Estimated 276hp and 322 lb-ft torque due to performance modifications. Very healthy for ~2200 lb vehicle!
o Eaton M90 supercharger
Interior ported / polished
o Aftermarket 3.5” blower pulley (stock is 3.8”), plus ~2 psi boost over stock
o Custom high-quality push / pull control capable type throttle
o Polished aluminum valve covers
o Engine top and bottom end stock
o IMI Performance Products, High Torque starter
Wired for starter crawl
• Exhaust
o Custom headers, long and equal length primary tubes (36”), ceramic coated inside and out.
o Stainless steel MagnaFlow muffler
o Exhaust note sounds amazing. Subdued and quiet idling and during regular driving. Aggressive and high-performance tone during hard acceleration.
• Transaxle
o Pro IRS Bus 091 by Rancho Performance Transaxles of Fullerton CA
o Super diff: 4.57 ring and pinion
o Weddle gear sets 1st through 4th
Ratios: 3.11, 2.08, 1.50, .82
Ratios matched the engine well. 1st is low, great for crawling but also fine for starting off in. Engine has so much low-end torque easily start off in 2nd. Fourth is geared to be an overdrive for cruising at reasonable highway speeds.
o Chrome moly diff cover
o Chrome moly pinion nut
o Case gussets
o Chrome moly 930 CV flanges
o Type 930 CV joints
Extra complete set of inner and outer joint rubber boots
• Hydraulic clutch
o CNC master and slave cylinder
o Stainless steel hard line and stainless steel braided, Teflon lined flex line.
• Jamar shifter with custom machined knob.
• Kennedy Engineered Products adapter plate between engine and transaxle
o Stage II, 9” heavy duty pressure plate with stock disc
• Brakes
o CNC single-lever cutting brake actuates rear brakes individually
o CNC four-wheel disc brakes
o CNC separate master cylinders for front and rear systems
o Stainless-steel hardlines with stainless steel braided Teflon lined flex lines, connected with premium Earl’s brand AN fittings.
o IPS Mechanical Parking Brake calipers mounted on rear, actuated by heavy-duty push-pull cables and Lokar ratcheting lever
• Custom dash / gauge pod
o Lighted, Autometer brand gauges
Speedometer with integrated odometer and tachometer
Coolant temperature
Oil pressure
Engine vacuum / supercharger boost pressure
Voltmeter
o Check engine LED lamp
o Horn button (Roadrunner, loud “Beep! Beep!” tone)
o Turn signal switches with LED indicator lamp
Actuate both together for hazard mode
o High beam switch with LED indicator lamp
o Low beam switch
o Running light switch
o Auxiliary light switch
o Fan automatic / force on switch with LED indicator lamp
o Fuel pump switch with LED indicator
o Boost on / disable switch with LED indicator
o Start button
o Ignition switch
o Spare button (toggles battery main on / off solenoid)
o OBDII diagnostic port, inside gauge pod
o Cigarette lighter style charge port, adaptable to USB
o Main (covered) keyed switch
o Two LED lamps light lower portion of face
o OBDII port inside controls enclosure, easily accessible by removing top cover
• Wheels / Tires
o Front: Centerline 15” x 3.5” / STA Super Traxion 7.0 – 15LT heavy duty 6 ply
o Rear: Centerline 15” x 7” / BFG T/A KO 33 x 10.5 R15
o Spare: 15" X 3.5” Race-Trim Off-Road Bead-Lock Wheel / STA Super Traxion 7.0 – 15LT
• Lights
o 8” KC head light pods, high beam / low beam with integrated LED cluster front running light / turn signals
o 1962 Impala style LED taillights in custom machined billet aluminum housings
Brake, turn, reverse indication
o LED bar 3rd brake light
o LED lighted rear license plate
o Two LED dome lights, one over front set and one over rear set of seats
• Custom roof rack with mounting provisions Baja essentials:
o Axe
o Shovel
o Hi-Lift brand jack, complete with spreader adapter
o Four, KC HiLiTES Daylighter auxiliary lights. Two 120W halogen flood and two 120W halogen spot.
o 8-foot lighted fiberglass whip. Quick / easy install removal. Uses any color / type of bulb that has an 1156 base.
• Other details
o Northern brand aluminum radiator
o Twin Spal electric cooling fans
Flexa-lite variable speed controller
o 100-micron pre, 10-micron post pump fuel filters
o 15-gallon fuel tank, Tygon tub
