Running Dyno again and have a video running. Repeats run after run. Several sets of headers, engine stands, exhaust systems, cooling tower for engine, dyno chillers go.
Most shop equipment gone, baking oven still here.
If you want a good dyno give me a call.
Above Added: Wed May 8, 2013, 10:10 am EST
Dyno set up and running and can send short video. Steelabrator oven is for sale, all other shop equipment sold.
Depac works great, however I just talked with Dave and he said he now has updates to windows. Depac is so good, the other companies are still trying to update to what Dave /Depac has accomplished years ago, and he has an update!
If want a work horse of a set up this is what you need..
Above Added: Thu April 25, 2013, 3:30 pm EST
Machine shop equipment for sale:
Clayton Depac 2,500 hp dyno with all the carts, great for injected or blown alcohol and extremely accurate for short track engines.
Hayden Steelabrator 250 airless shot peen machine and
Hayden 500 series oven w/stack burn for epa approval 9,000
Kwikway 856 block and head surfacer, surface BBC and Chrysler blocks, extra grinder wheels go with unit. Will convert to carbide cutters for 800. 4,500
Doall surface grinder, hand crank, magnetic chuck 450.
All shop equipment is in excellent working order, I was a small one man shop, usage very low. Will consider full or partial trade for car for wife, street rod, restaurant vending equipment or a truck camper.
See the add on www.racingjunk.com Ad #2139947
Above Added: Tue March 15, 2011, 8:23 pm EST
Info for thought, I recently was helping a friend on his dyno and it lost the tach signal. The engine rpm shot to the MOON! What happend was the dyno software thought the engine rpm was too low, so it dumped the water pressure! THIS WILL NOT HAPPEN with this Clayton/Depac dyno set up. If you loose total power to this dyno, the engine will just stay at the same rpm, so when you are shopping around, ask the person what happens to your engine if the dyno looses power, yep, your right YOU ALSO LOOSE YOUR 30,000 thousand dollar blown alky engine! Look around and ask questions...
Above Added: Mon February 28, 2011, 8:48 pm EST
If you have a fuel pump flow bench, you also can adapt Depac to it. Take the flow sensors and plug it in, you will need a tach signal for rpm. What I used was a 120 tooth sproket, because the pump runs at half speed, which means double the speed of the signal, so Depac thinks it is engine speed not the pump speed..Want to see what the hi speed does for pressure under loads without beating up your engine? Then set up your fuel system first and you are ready to dyno, fine tune and away you go.
The Depac program allows you to convert fuel flow from gph or pounds of fuel per hour. For alky, it is 1 pound of fuel to 1 horsepower..if you have 2000 horse, make sure you have at least 2000 pounds of fuel. In seconds you can overlay ANY base dyno run then call up your improved fuel system curves and look at them on real life screens....Can these other programs do this? Just think about what you can do with Depac...Do you want to be the best tuner in the country? Depac makes it easy for you..
Above Added: Sun January 23, 2011, 11:21 am EST
Please note that I am recieving bids on Dyno and Serdi.
Other shop eqipment available, if you are looking for something let me know. BHJ fixtures, Kwikway boring bars etc...BBQ vending kitchen coming soon and will not have the time for the machine shop.
Above Added: Tue January 18, 2011, 8:39 pm EST
Main shaft for dyno is 2.250"
Above Added: Mon January 3, 2011, 3:54 pm EST
Dyno will run in both directions, as we did reverse rotation engines. All the heat exchangers and plumbing go with unit.
Above Added: Mon January 3, 2011, 3:48 pm EST
two fuel systems, one for gas and one for alky. If you run big horsepower, this dyno will handle it. you can switch engines with the extra carts so one person can make changes out in the shop while you run another.
Above Added: Tue December 28, 2010, 5:36 pm EST
Dyno has manual load so you have complete control of engine at all times. Discharge of water brake is done with a simple gate valve or you can use jets that control amount of water exhausted for a smooth acceleration rate. Depac is so exact in how it measures power, is does not matter if you sweep fast or slow, power curves are EXACTLY the same. Depac is by far the best and is why most professional shops/teams use it. The Depac program is so expandable you have access to the input data to build other programs, I adapted to my airflow bench for reading cylinder head data and also my alky fuel bench for flowing systems. This Clayton absorber can be used for higher torque loads when run direct, rpm max of 5,000. I set up with a 1.5 reduction to run in the upper rpm ranges 8,000.
This dyno has run 4cyl circle track engines of 100 horse, up to blown or injected alky engines. With the blower engines, things happen quickly which is why I wanted to "drive" or controll the engine at all times. After you get use to the feel on the throttle stick, you will be able to tell while you are driving, if you have a runner or not and have to do more research.The Serdi is a 100 with LOTS of tooling.
Above Added: Sun December 12, 2010, 10:18 am EST
Complete Clayton engine dyno, set up with Depac, EVERY run will repeat! So exact to be sure you are getting great results from your dyno testing, make a run and see it on the screen instanty. pull up last years run to overlay the graph to see the improvements. I have added expansion boxes for many data inputs, blower pressure vrs top hat vacuum, several temp inputs etc, two fuel meters. Dyno can be seen on you tube, we did the Dura Lube comercials. Comes with 3 engine stands and all headers. You do NOT need any pumps, just 30 psi of water pressure to inject into wheel. Everything I have for engine running will go with it. Also have Serdi seat machine to go also. Expanding BBQ vending venture.