{"id":89991,"date":"2023-03-17T08:02:11","date_gmt":"2023-03-17T15:02:11","guid":{"rendered":"https:\/\/www.racingjunk.com\/news\/?p=89991"},"modified":"2023-03-17T08:02:13","modified_gmt":"2023-03-17T15:02:13","slug":"the-easy-mechanical-valve-lash-procedure-part-1","status":"publish","type":"post","link":"https:\/\/www.racingjunk.com\/news\/the-easy-mechanical-valve-lash-procedure-part-1\/","title":{"rendered":"The Easy Mechanical Valve Lash Procedure Part 1"},"content":{"rendered":"\n
\"\"<\/figure>\n\n\n\n

Need to check valve lash in a fresh cam or new engine? Part 1 of Wayne Scraba’s new two part series will show you how.<\/h2>\n\n\n\n

Setting valve lash with a mechanical cam isn\u2019t uncommon (in truth, absolutely necessary and even a lot of vintage high performance cars were solid lifter equipped). No secret we\u2019re sure. Most professional engine builders will tell you the lash on a race car should be checked (at least) between each event. Some drag racers (both Pro and Sportsman) prefer to see lash checked between rounds. Aside from ensuring the lash is in good shape, a really good reason for this is it gives you the opportunity to see if something is amiss inside the engine. For example, the engine might have experienced a bent valve or a broken lifter. You can spot this before the carnage really begins.

When you examine the cam spec card for your engine, you\u2019ll find the valve lash is almost always listed \u201chot\u201d. But how do you know where to start with a fresh cam or new engine? If you\u2019re running a pretty common aluminum head\/iron block combination, start by setting the cold lash 0.006-inch tighter then the hot lash recommended by the cam manufacturer. Fire up the engine and allow it to run until it\u2019s up to operating temperature. Shut off the engine and lash the valves on one cylinder to the recommended hot lash.<\/p>\n\n\n\n


Allow the engine cool down (I usually leave it overnight), and check the lash on the pair of valves that were previously set hot. The lash that you now check will be the correct cold lash setting you can use from now on. Set the balance of the valves to the \u201cnew cold setting\u201d and you\u2019re done. For the most part, you\u2019ll never need to check it hot again unless there is a change made somewhere in the valvetrain.

Although there are several different methods to set the lash, the \u201cbase circle\u201d or \u201cExhaust Opening\/Intake Closing\u201d (\u201cEO-IC\u201d) method recommended by the folks from Jesel is very easy (and common too):

\u201cStarting at #1 cylinder, rotate the engine until the #1 exhaust rocker just starts to open the exhaust valve. Set the valve lash on #1 intake rocker at this time. Continue rotating the assembly and stop when #1 intake rocker starts returning from full lift. The lash on #1 exhaust can now be set. Continue this procedure for the remaining cylinders following the engines firing order.\u201d

In contrast is the standard OEM Chevy method of lashing valves (sometimes called the \u201cChilton Manual or Chevy Shop Manual Method\u201d). It requires a degreed damper of some sort, or at least a timing tape along with a good, easy to see and easy to read timing pointer. The engine must be turned over until number one cylinder is in the firing position (TDC). With this arrangement, valves are set at specific points along the crankshaft rotation. On a V8, you\u2019ll set intake number 2 and 7 as well as exhaust number 4 and 8. The engine is turned over 180-degrees and you\u2019ll set intake number 1 and 8 as well as exhaust number 3 and 6. Turn the engine over 180-degrees to number six firing position and set intake number 3 and 4 as well as exhaust 5 and 7. Finally, turn the engine over 180 degrees and set intake number 5 and 6 as well as exhaust 1 and 2.

The typical Mopar method for small block and big block engines (\u201cA\u201d engines, \u201cB\u201d and \u201cRB\u201d engines as well as \u201cHemi\u201d power plants) is the same as above. Other vehicle manufacturers use similar procedures, but with different numbering sequences.

If you\u2019re using the OEM method of valve lash, you\u2019ll need a well-marked harmonic damper (balancer). The reason of course, is you\u2019ll need to know where TDC is on the damper along with a half turn (180-degrees). If you don\u2019t have a degreed balancer, Mr. Gasket and others sell timing tapes for various applications. Typically, these tapes fly off with regularity. The fix is a little tedious, but not complex: Remove the paint on the damper face, clean it with metal prep and carefully install the tape. Once dry, coat the surface with clear paint (lacquer if you can find it). With this process, chances are pretty good the tape won\u2019t fly off abruptly.

Next issue, we\u2019ll devote space to the tools that happen to go along with lashing valves. They\u2019re not exotic and for the most part, they\u2019re certainly expensive (there are some exceptions though). For a closer look at valve lash basics, check out the accompanying photos:
<\/p>\n\n\n\n