{"id":60722,"date":"2019-03-19T11:04:12","date_gmt":"2019-03-19T18:04:12","guid":{"rendered":"https:\/\/www.racingjunk.com\/news\/?p=60722"},"modified":"2019-03-19T11:04:12","modified_gmt":"2019-03-19T18:04:12","slug":"using-engine-vacuum-to-diagnose-performance-issues","status":"publish","type":"post","link":"https:\/\/www.racingjunk.com\/news\/using-engine-vacuum-to-diagnose-performance-issues\/","title":{"rendered":"Using Engine Vacuum to Diagnose Performance Issues"},"content":{"rendered":"

\"Using<\/p>\n

Years ago, my father\u2019s main mechanic at the Chevron station, Billy Jeff \u2013 BJ \u2013 gave me a vacuum gauge as a birthday present. BJ was probably the best mechanic I\u2019ve ever known. A full-blooded Native American Indian, he\u2019d often climb up after me into an engine bay (he was only five feet tall) to do stuff and explain what he was doing and why he was doing it.<\/p>\n

Dad and BJ, more so BJ, taught me early on that a vacuum gauge can tell you almost everything you need to know about your engine\u2019s health as long as you know how to interpret what you\u2019re seeing on the gauge, hearing and feeling. Put these three pieces of information together and you\u2019ll know if you\u2019re looking at an easy fix or a complete engine rebuild.<\/p>\n

You should never scrimp on your vacuum gauge<\/a>. It\u2019s one of those tools for which you should pay more so you get the best quality you can afford. It needs to read up to 30 inches of mercury (In\/Hg) of vacuum. Low quality gauges can leak internally and give unreliable readings. Since it\u2019s hopefully a fine instrument, treat it properly. Keep it in the case it came in if possible. Keep it clean. Don\u2019t bang or drop it.<\/p>\n

Begin your engine check-up by making a thorough preliminary inspection. Pop the hood and look over the engine compartment with the proverbial fine-tooth comb. Check all vacuum lines and fittings for cracks or breaks. Test vacuum connections to make sure they\u2019re tight. Make sure any ports or fittings that are supposed to be plugged are plugged properly. Fix anything you find here.<\/p>\n

\"Using<\/p>\n

Start the engine and listen for leaks in several locations around the engine bay. Now perform the wiggle test. With the engine running, wiggle the vacuum connections and jiggle the lines while listening for the hiss or changes in the engine that vacuum leaks cause. I like to spray carb cleaner around the base of the carburetor and intake manifold as well as all the vacuum lines, check valves and connections. A vacuum leak will suck the carb cleaner into the engine and cause the RPM to fluctuate rapidly.<\/p>\n

Next, go for a test drive. I like to push the hose on my vacuum gauge through the firewall\/bulkhead (using an existing penetration) and connect it to a direct vacuum source like the manifold (more on this later) so I can watch my vacuum gauge as I\u2019m test driving the vehicle. I put it on the dash above the speedo so I can see the fluctuations as I\u2019m driving and link them to the driving conditions under which they occurred. So I can test the vehicle driving as my customer does, I get some neighborhood, city and highway driving during my 30 minute run.<\/p>\n

\"Using
Image courtesy Holley<\/figcaption><\/figure>\n

When diagnosing engine performance problems using vacuum, you must use a direct source of vacuum, such as the vacuum tap on most intake manifolds. A good source for many is the vacuum line going to the transmission. No matter where you get your vacuum source, make sure it\u2019s not ported.<\/p>\n

\"Using
This chart shows vacuum readings you might see and what they mean.<\/figcaption><\/figure>\n

Most engines will run 17-21 In\/Hg while idling at normal operating temperature. Obviously this isn\u2019t true for huge lopy cams<\/a> that can barely idle. Mild performance cam profiles should give vacuum readings of between 15-20 In\/Hg, although their performance profiles may decrease average vacuum by approximately three In\/Hg and cause mild \u201clopiness\u201d with attendant vacuum fluctuations as overlap increases.<\/p>\n

\u201cFlooring it\u201d should cause vacuum to drop quickly, maybe to zero. Releasing the accelerator quickly after a few seconds should cause vacuum to quickly bounce back up to above normal (usually around 25 in\/Hg) then quickly return to normal (17-21 \u201c\/Hg) as engine RPM slowly returns to idle.<\/p>\n

Vacuum decreases slowly when the pedal is put to the floor. It should drop almost to zero for an instant when you accelerate quickly. A restriction in either the intake or exhaust is indicated if the gauge shows vacuum decreasing slowly instead of quickly. Something like a plugged cat or muffler is usually the culprit here.<\/p>\n

As stated, a \u201cstock\u201d engine should pull 17-21 In\/Hg of vacuum at idle. The cool thing about using a vacuum gauge to diagnose engine problems is that different engine problems show themselves by vacuum readings in different ranges. For example, if you\u2019re seeing vacuums readings at idle of:<\/p>\n