Water in Head 2-leaking head studs

Old 08-15-2008, 03:54 AM
  #11  
curtisreed
Senior Member
RACING JUNKIE
 
curtisreed's Avatar
 
Join Date: Feb 2004
Location: KIEFER, OK.
Posts: 1,312
Default

x3 thread sealer works for me too.
curtisreed is offline  
Old 08-15-2008, 04:34 AM
  #12  
suicidebomb
Senior Member
RACING JUNKIE
 
Join Date: Jul 2007
Location: Independence, Missouri
Posts: 1,181
Default

X4
suicidebomb is offline  
Old 08-15-2008, 05:47 AM
  #13  
bjuice
Administrator
RACING JUNKIE
 
bjuice's Avatar
 
Join Date: Apr 2003
Location: Greenville s.c.
Posts: 3,236
Default

i have personally used teflon tape with ULTRA GREY Permatex sealer smeared on top of the teflon tape....and not one drop of water has leaked or seeped thru the head studs....

this is the method i have used in the past with 100% reults and no issues removing studs at a later date..



just another idea of how to do it.

Brian
__________________
Bjuice..

"I'M YOUR HUCKLEBERRY ! "
bjuice is offline  
Old 08-20-2008, 06:45 PM
  #14  
cncmotorsports
Senior Member
MASTER BUILDER
 
Join Date: Apr 2003
Location: Brookings South Dakota
Posts: 244
Default

If they are ARP studs, take them to a buffing wheel and give them a good buffing, then try thread sealer or we have even used the brand right stuff silicon, just another idea we have experimented with and have had great success.
cncmotorsports is offline  
Old 08-21-2008, 09:28 AM
  #15  
dynaguy03
Senior Member
MASTER BUILDER
Thread Starter
 
Join Date: Feb 2008
Location: New Jersey
Posts: 133
Default Resealing threads on the head studs

Last night i went thru removing 1 stud at a time and a serious cleaning procedure , remove the stud, clean in laquer thinner, wire wheel the threaded area, reclean with brake cleaner, use a small wire bottle brush with thinner and clean the block side hole, then goop it up with the Loctite 567 , Resealing with a high end loctite 567 thread sealer.. it will seal to 1000 psi in 1 hr - 10,000 psi in 24hrs, good to 450f .. this crap better work it was 75 bucks for a 250ml tube!!!
Tonight i will put water in and pressure test it... I really hope this works!!
dynaguy03 is offline  
Old 08-21-2008, 06:50 PM
  #16  
dynaguy03
Senior Member
MASTER BUILDER
Thread Starter
 
Join Date: Feb 2008
Location: New Jersey
Posts: 133
Default Resealing worked

Ok 4hrs of removing -cleaning and installing and re- torqueing - put water in the system- pressureized it to 16 lbs and no water leaking from the head studs. Looks like the Loctite 567 does what it says it does.
Tomorrow i will run it thru some heat cycles..and see what happens.

Thanks for all the suggestions

oh .. and the guy who built the motor did 90% of the work ..hell the motor never made it out of the garage!.. But it was good to see someone stand behind there work.
dynaguy03 is offline  
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -