prostreet1972

Guess I'll post my slow car.

72 Chevelle

It is back halfed with a ladder bar setup. It has one fiberglass seat, carpet and original dash and door panels. Fiberglass hood, trunk lid, and front a rear bumpers. Weld Drag star wheels, 15x14 in rear with a 29.5x11.5W slick (30.4x14 actual) How much do you think it weighs?? 5.14 Rear gear.

Motor/Trans:
350 stock bore, stock flat top 4 valve relief, double hump heads 64cc 1.94/1.5. I cut a lot out of the intake ports to get them to flow into my ported Weiand Team G intake. 750 DP 150shot sniper plate kit. Stock bottom end. According to desktop dyno I have 370hp@5500 and 380ftlbs@4500. then with 150 shot i have 520hp@5500 and 555ftlbs@4500.

Cam is a Lunati Bracket Master solid flat tappet
Lift is .500/.515
dur. @.050 is 256/270
adv. dur. is 300/310
lobe Sep. 112
Int. cl 108

Trans is a TH350 with shift kit, nothing special. It is a footbrake car.

So far best in 1/8th mile on motor is 8.27@83 1.88 60ft. (this is with a blue racer cam .465/.488 lift hyd. flat tappet) with 100hp shot it went 7.72@92

Tod74

My 72 chevelle weighs around 3600 lbs

john858

built car for my best friends wife,she didn,t want to run below 7.00's in 1/8th (didn't want to cross over ever )
built a 402ci bb chev with mild 595 lift cam ,360 horse heads (stock nothin done to them) on alc.,2900lb car runs between 6.76 & 6.79& she loves it & love to cross over to .

SharpMotorsports

1968 camaro full chromolly chassie glass frontend all steel body with a 292 cu in small block CHEVY g-force 5 speed strang ford nine inch rear 6.00 gear ran 9 40 at 143 at moroso in march running low 9 50's in ohio

gearhead1011

1997 Ford Probe chromolly chassis Strange struts, shocks & brakes. 4 link/wishbone rear. 370 inch windsor, 5 speed liberty 3.16 low gear 5.43 rear. 2,250 lbs with driver. 5.45 1/8 mile at 126 mph. I've only made one 1/4 mile shot and it got out of the groove and I had to lift but managed a 8.76 @ 152 mph. It should go 8.50s.

curtisreed

Finally got my junk running ok. 383 sbc, 11.3-1, KB forged pistons, .600,.640 282,290 .106 lca solid roller, 1.6 rocker, track 1 heads, scat crank, h-beam rods, Victor jr., Rupert methanol carb, pg 1.76, 4.88 gear, 16.5-33 tire. I'm not sure of the weight yet . No faster than it is I tell everyone it is about 3000lbs. LOL Best pass so far in 2550da.

1.328 60ft
3.8611 330ft
6.081 660ft
109.28 mph

Not really sure what it will run in the 1/4.



Lost this round by .0030 oh well there's always the byback window.

Curtis

Scotty2

Went a 8.239 @ 164.276 this past weekend .Track wasn't that great ...... they wouldn't spray passed the 100' mark and the car was skating when I would pull high gear.

shimm

65 mustang..302 + .30....11.5 KB pistons.eldebrook heads. 550. lift solid cam.650 holley.c4 manual valve body.9in.w/spolled 456 gears.
traction bar rear...best i got from it all has been a 801. in the 1/8 last year..this year can only get 8..40 w/new trans an convertor..3600 stahl.
best 60.ft. 1.80
time to refreshen the moter during winter an roller cam for next year

radicalz

.....Sweet ride Scotty....Ford powered or Chevy Powered....either way it is flat out flyin...good job.....had mine outy again this summer mad best pass off the bottle 10.34 @ 134.65 mph....did not do the bottle yet added another system...hehehehe.....best with the 300 plate was 9.85 last year.... working the bugs out of new system b4 blasting down the 1/4 mile....maybe in the spring i can rake it one time.... :wink: :wink:

W31350

64 chevy II.
9.5:1 350
edelbrock rpm heads
rpm air gap intake
750 holley
.555 hyd cam
th350 4000 stall
d60 w/ 4.56

car went 8.01@87mph w/ a 1.8 60ft. ops: