finished my buddies sbc!

Old 08-23-2009, 08:01 PM
  #1  
bowhay
Senior Member
EXPERT BUILDER
Thread Starter
 
Join Date: Nov 2008
Posts: 263
Default finished my buddies sbc!

ok so weve been workin on this 350 sbc .060 over for about 5 months now and we're finally done
its got a scat all forged rotating assembly, forged flat tops, and afr alluminum heads 210 cc runner and 205int and 160exh valves, harland sharp 1.5 rockers and a lunati 525int and 540exh cam, air gap manifold and 750 carb
hes wantin a few guesses on power, i said close to 525 give or take
what do yall think?
bowhay is offline  
Old 08-23-2009, 08:24 PM
  #2  
kwkracing
Senior Member
RACING JUNKIE
 
Join Date: Dec 2004
Location: austin texas
Posts: 729
Default

5 months? its hard enough to keep a motor clean for 2 hours while assembling....lol

Good job, i hope it works out well for you 2
kwkracing is offline  
Old 08-23-2009, 08:25 PM
  #3  
Tod74
Senior Member
RACING JUNKIE
 
Join Date: Sep 2007
Posts: 4,137
Default Re: finished my buddies sbc!

Originally Posted by bowhay
hes wantin a few guesses on power, i said close to 525 give or take
what do yall think?
I think yall was smoking weed.

That things good for at least 600...maybe 625.
Tod74 is offline  
Old 08-23-2009, 08:29 PM
  #4  
MEMRACING62
Senior Member
RACING JUNKIE
 
Join Date: Sep 2007
Location: orland pk il
Posts: 2,399
Default

CHASIN WOMEN AND DRINKIN HOT TEXAS BEER AGAIN :roll:
MEMRACING62 is offline  
Old 08-23-2009, 08:43 PM
  #5  
kwkracing
Senior Member
RACING JUNKIE
 
Join Date: Dec 2004
Location: austin texas
Posts: 729
Default

:roll:
kwkracing is offline  
Old 08-23-2009, 08:50 PM
  #6  
OneBadGMC
Senior Member
RACING JUNKIE
 
Join Date: Sep 2007
Location: Belleville, IL
Posts: 658
Default Re: finished my buddies sbc!

Originally Posted by Tod74
Originally Posted by bowhay
hes wantin a few guesses on power, i said close to 525 give or take
what do yall think?
I think yall was smoking weed.

That things good for at least 600...maybe 625.
You mean all low compression, small cammed, 350 chevy's don't make 1.5 HP/CID???

Dammit! :shock:
OneBadGMC is offline  
Old 08-24-2009, 09:17 PM
  #7  
cepx111
Senior Member
RACING JUNKIE
 
Join Date: May 2006
Posts: 2,044
Default

With the low compression and the limiting intake> I'd say maybe 450HP-500 tops.
cepx111 is offline  
Old 08-27-2009, 09:24 PM
  #8  
russ67chevelle
Senior Member
EXPERT BUILDER
 
Join Date: Jan 2005
Posts: 336
Default

u need to tell more info on cam(solid or hydraulic then roller or flattappet)
also what is compression ratio?

off top of my head ill guess 450 would be doing pretty well if 10:1 compression hydraulic flat tappet....tell us more!!!


by the way the intake is fine unless u regularly take er up to 7000 rpms or higher
russ67chevelle is offline  
Old 08-29-2009, 02:06 PM
  #9  
bowhay
Senior Member
EXPERT BUILDER
Thread Starter
 
Join Date: Nov 2008
Posts: 263
Default

hydrolic flat tappet, with a 10.5 to 1
bowhay is offline  
Old 08-29-2009, 02:22 PM
  #10  
MEMRACING62
Senior Member
RACING JUNKIE
 
Join Date: Sep 2007
Location: orland pk il
Posts: 2,399
Default

I WOULD AGREE WITH RUSS67CHEVELLE 450-475
MEMRACING62 is offline  

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -