A-ARM 2x3TUBECHASSIS HELP

Old 02-05-2012, 05:03 AM
  #1  
injectedrat68
Junior Member
APPRENTICE
Thread Starter
 
Join Date: May 2003
Location: Broad Brook,CT.
Posts: 23
Default A-ARM 2x3TUBECHASSIS HELP

I just picked up an old 2x3 a-arm front clip I think it an A. R .T.type. I have a back half 68 camaro Round tube chassis. OK, heres the question, i dont have the old front clip in the car any more and was trying to figure out where i should mount this clip and what height the center of spindle is. The other prob. is someone cut the rest of the fram connections off. I only have the front clip to where it would start to go under the fire wall. If you need pics i will get them or if eaiser i can call.Thanks for reading. Paul
injectedrat68 is offline  
Old 02-05-2012, 08:51 AM
  #2  
TheYellaBrick
Senior Member
RACING JUNKIE
 
TheYellaBrick's Avatar
 
Join Date: Mar 2008
Location: Emmett, Idaho
Posts: 7,334
Default

Post up some good clear pics and you'll get more help. Lot of fabricators on here.
TheYellaBrick is offline  
Old 02-05-2012, 10:43 AM
  #3  
coolracing
Senior Member
MASTER BUILDER
 
Join Date: Jan 2008
Location: Yooper
Posts: 168
Default

As Double D said ya need to post some pics! But shouldnt be that big of a deal.
coolracing is offline  
Old 02-05-2012, 11:09 AM
  #4  
injectedrat68
Junior Member
APPRENTICE
Thread Starter
 
Join Date: May 2003
Location: Broad Brook,CT.
Posts: 23
Default post subject

Thanks for replying. i will get some up
injectedrat68 is offline  
Old 02-05-2012, 07:49 PM
  #5  
zipper06
Senior Member
RACING JUNKIE
 
Join Date: Jan 2006
Location: La.
Posts: 2,890
Default Re: post subject

Originally Posted by injectedrat68
Thanks for replying. i will get some up
Don't know if you know already or not but A.R.T. is back up and running after being shut down a while, you might be able to get the mounting pads from them, maybe give them a call.

Zip.

http://www.appliedracing.com/
zipper06 is offline  
Old 02-06-2012, 02:17 AM
  #6  
injectedrat68
Junior Member
APPRENTICE
Thread Starter
 
Join Date: May 2003
Location: Broad Brook,CT.
Posts: 23
Default post subject

I have pics, cant figure out how to get them up
injectedrat68 is offline  
Old 02-06-2012, 09:54 PM
  #7  
zipper06
Senior Member
RACING JUNKIE
 
Join Date: Jan 2006
Location: La.
Posts: 2,890
Default Re: post subject

Originally Posted by injectedrat68
I have pics, cant figure out how to get them up
you have a PM

Zip.
zipper06 is offline  
Old 02-07-2012, 07:24 PM
  #8  
zipper06
Senior Member
RACING JUNKIE
 
Join Date: Jan 2006
Location: La.
Posts: 2,890
Default Re: post subject

Originally Posted by injectedrat68
I have pics, cant figure out how to get them up
Pictures post for njectedrat68

Zip.




zipper06 is offline  
Old 02-07-2012, 07:57 PM
  #9  
TheYellaBrick
Senior Member
RACING JUNKIE
 
TheYellaBrick's Avatar
 
Join Date: Mar 2008
Location: Emmett, Idaho
Posts: 7,334
Default

GOOD ! These show us what you are working with !
Now we need 4 pics of the car you want to mount this in, please. Ideally one facing the firewall, a shot of the underbody at the firewall, one facing forward from the rear seat area, and one facing forward from the rear end area.
TheYellaBrick is offline  
Old 02-08-2012, 02:10 AM
  #10  
injectedrat68
Junior Member
APPRENTICE
Thread Starter
 
Join Date: May 2003
Location: Broad Brook,CT.
Posts: 23
Default post dubject

Im running a stock fire wall on 68 camaro. The plan was to tie into the main cross member behind the drive seat where my ladder bars are.Because the car sits low I think if I put in the front clip i have to cut away the floor either all or just where the rails would tie into the cross member. I will get some pics to Zip to post. Thanks Zip
injectedrat68 is offline  

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -