bad engine junk

Thread Tools
 
Old 11-01-2010, 01:52 PM
  #1  
puggles2
Junior Member
SHOW GUEST
Thread Starter
 
Join Date: Nov 2010
Posts: 3
Default bad engine junk

I purchased an engine from John Janosky from Florida. His ad said it was a new motor and never been run, That's a lie. We got the motor in the car, it ran 105.75 in the 1/8 th mile, and it was blowing smoke. I tried to telephone him from the track, but he did not respond and up until today, he has never responded back to me. The season is over and the motor is junk. He welded the block and tried to cover it up but he did not do a very good job. You can see where the block had rusted and the end caps of the crank shaft bolts were hitting the side of the block when it was rotating and
wore the bolts down. It was hitting in four different places and all four places are rusted. One of the pistons cracked the side of the block. John
Janosky put that block together knowing that he was putting together an
old rusty, welded-together motor and selling it for $5500.00. Today, that same piece of "crap" that he sold us isn't worth a $1.00. JOHN JANOSKY
SELLS REALLY JUNK EQUIPMENT.
puggles2 is offline  
Old 11-01-2010, 02:01 PM
  #2  
ajk
Senior Member
DYNO OPERATOR
 
Join Date: Jun 2009
Location: Wi
Posts: 522
Default

Was the ad for the engine on race junk? If yes what is the ad number. Any pictures?Now i just have to ask if it was never run the first time it was run was down the track? No break in? If it was broke in did you have any problems arise during breakin or during tuning the motor before going to the track ?
ajk is offline  
Old 11-01-2010, 02:06 PM
  #3  
Harbone
Moderator
RACING JUNKIE
 
Harbone's Avatar
 
Join Date: Aug 2007
Posts: 4,042
Default

did you inspect the motor before purchasing? If it was that noticable (the welds) why didnt you catch it before the purchase? I dont want to sound harsh but I would never purchase a motor without at least dropping the pan, pulling the intake or at least 1 head.
__________________
Chris

As close to "Normal" as I can get...
Harbone is offline  
Old 11-01-2010, 02:20 PM
  #4  
Scooterz
Senior Member
RACING JUNKIE
 
Join Date: Mar 2006
Location: EUGENE,OR.
Posts: 3,391
Default

This is unfortunate scenario that happens way to much these days. Motors are a volatile item to sell alone by nature. With further investigation, sometimes it is not always a case of being "Junk" to begin with. Other times, pulling a pan or valve cover would have stopped a whole lot of pain down the road. At any case, if it was sold here, list the ad# & see if the seller would come on here to explain.
Scooterz is offline  
Old 11-01-2010, 02:27 PM
  #5  
Tod74
Senior Member
RACING JUNKIE
 
Join Date: Sep 2007
Posts: 4,137
Default Re: bad engine junk

Originally Posted by puggles2
You can see where the block had rusted and the end caps of the crank shaft bolts were hitting the side of the block when it was rotating and
wore the bolts down. It was hitting in four different places and all four places are rusted. One of the pistons cracked the side of the block..
this makes no sense to me.
Tod74 is offline  
Old 11-01-2010, 02:36 PM
  #6  
MEMRACING62
Senior Member
RACING JUNKIE
 
Join Date: Sep 2007
Location: orland pk il
Posts: 2,399
Default

Same here, makes no sense... :?
MEMRACING62 is offline  
Old 11-01-2010, 02:45 PM
  #7  
Scooterz
Senior Member
RACING JUNKIE
 
Join Date: Mar 2006
Location: EUGENE,OR.
Posts: 3,391
Default

I thought I was the only one who did not understand... is it somehow crank end-play, or was it an overzealous hammer trying to get them out (bolts), how did they hit the "side of the block" when it goes through the block.... can't figure it out either.
Scooterz is offline  
Old 11-01-2010, 02:48 PM
  #8  
ajk
Senior Member
DYNO OPERATOR
 
Join Date: Jun 2009
Location: Wi
Posts: 522
Default

Originally Posted by Rigsby
I thought I was the only one who did not understand... is it somehow crank end-play, or was it an overzealous hammer trying to get them out (bolts), how did they hit the "side of the block" when it goes through the block.... can't figure it out either.
X2!!!
ajk is offline  
Old 11-01-2010, 03:02 PM
  #9  
contagious
Senior Member
MASTER BUILDER
 
Join Date: Nov 2005
Location: Mobile,Al.
Posts: 127
Default motor

Maybe the rod bolts were hitting the side of the block.?stroke crank.Trying to read between the lines here.!!!!
contagious is offline  
Old 11-01-2010, 03:58 PM
  #10  
mopar1968
Senior Member
RACING JUNKIE
 
mopar1968's Avatar
 
Join Date: Dec 2006
Location: Abingdon,Virginia
Posts: 3,578
Default

That is the only thing i can think of is the rod bolt's hitting :!: I am cornfused also :!: JMO Mark
mopar1968 is offline  


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -