Results 1 to 3 of 3

Thread: recamming the SBC 406 questions

  1. #1
    Senior Member DYNO TECH
    Join Date
    Aug 2007
    Location
    Colebrook Connecticut
    Posts
    425

    recamming the SBC 406 questions

    going with an isky hydraulic roller
    cam card here.
    anyone use this cam ?
    i got 3:93 rear ratio and 2500 stall converter on a built th350.
    brodix -10 aluminum heads
    11:1 compression
    also I got 150 nitrous shot on the plate.
    will this cam work ????
    thoughts???



    TIMING CHART

    PART NUMBER: 211282/294GRIND NUMBER: rr-282/294ENGINE INFO: CHEVY SMALL BLOCK V8 305-350 CU.IN. 1988-UPAPPLICATION: SPECIAL REMARKS: HYDRAULIC ROLLERPRODUCT USE: STREET/STRIPRPM RANGE: 3000-7000Valve lift is calculated with zero lash and rocker ratio of 1.5INTAKE TIMING DURATION: 282deg.OPEN: 31BEFORE TDCCLOSE: 71AFTER BDCCAM LIFT: .353"VALVE LIFT: .530"VALVE LASH: .HOT.COLDEXHAUST TIMING DURATION: 294deg.OPEN: 77BEFORE BDCCLOSE: 37AFTER TDCCAM LIFT: .367"VALVE LIFT: .550"VALVE LASH: .HOT.COLD
    LOBE CENTER: 110 deg.OVERLAP: 68 deg.CAM ADVANCE: 0 deg.THE ABOVE TIMING IS CHECKED AT .020(OPEN) LIFTER RISE.020(CLOSE)The following timing is taken at .050" lifter rise and gives a more accurate determination of camshaft position.INTAKE DURATION: 234deg.OPEN: 7BEFORE TDCCLOSE: 47AFTER BDCEXHAUST DURATION: 246deg.OPEN: 53BEFORE BDCCLOSE: 13AFTER TDCRECOMMENDED ISKY CAM KIT PARTS AND SETUP INFORMATION

    LIFTERS: USE STOCKLIFTER TYPE: HYDRAULIC ROLLERSPRING: 6105TYPE: dual W/DAMPERDIA.: 1.430"RATE: 330 lbs per inchINSTALLED HEIGHT: 1.812"SEAT PRESSURE: 135 lbsOPEN PRESSURE: 315 lbsCOIL BIND: 1.120"SPRING SHIMS: # 2STEEL RETAINERS: 507-STATITANIUM RETAINERS: 60-TIPUSHRODS: 203-HG-.460"TYPE: heat treated non-adjLENGTH: 7.200"DIA.: 5/16"ROCKER ARMS: 204TYPE: rollerRATIO: 1.5VALVE LOCKS: VL-32VALVE LOCKS: VL-32REV KIT:

    home | what's new | tech info | news | catalog | apparel | about | contact
    2002 Isky Racing Cams. All rights reserved.

  2. #2
    Senior Member DYNO TECH
    Join Date
    Aug 2007
    Location
    Colebrook Connecticut
    Posts
    425
    yeah hey thanks for the helpful advice!

  3. #3
    This is the cam I used in my 69 camaro with a 406 howards cam part #110265-10 works good what ever cam you use you will need more stall converter nice car


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Copyright © 2005-2016 RacingJunk.com All Rights Reserved.

Designated trademarks and brands are the property of their respective owners. Use of this Web site constitutes acceptance of the RacingJunk.com
Terms of Use, Classifieds Disclaimer, Privacy Policy, and Cookie Policy