condensation on plugs?

Old 12-02-2009, 05:30 PM
  #1  
cam67152
Senior Member
MASTER BUILDER
Thread Starter
 
Join Date: Apr 2009
Location: B.C. Canada
Posts: 145
Default condensation on plugs?

I just finished firing my BBC 496, ran great! set the timing checked all the usual thingsevery thing seemed fine till the next day, I pulled a plug and it looked like it had water on it, I retorqued the intake (which I had milled to fit) checked the oil for water, it was fine (drained and changed filter) Started it up ran fine, next day water on the plugs again? Presurized rad, no leak down. Is this condensation? or a bigger problem?

:? thanks for any advice in advance.
cam67152
cam67152 is offline  
Old 12-02-2009, 05:43 PM
  #2  
BEAST477
Senior Member
RACING JUNKIE
 
BEAST477's Avatar
 
Join Date: Feb 2007
Location: Michigan
Posts: 1,900
Default

It could be condensation. How long are you running it? Are you running it long enough to bring the oil and coolant temps up to 180-200 degrees, if not that can cause condensation. I've had it happen before when taking off valve covers to check lash.
BEAST477 is offline  
Old 12-02-2009, 09:56 PM
  #3  
cam67152
Senior Member
MASTER BUILDER
Thread Starter
 
Join Date: Apr 2009
Location: B.C. Canada
Posts: 145
Default

I did bring it up to temp in the morning to set timing. But started it up later that night for a short time. Should i try bring it up to temp, let it cool then check the plugs? Then check them them again the next day. By the way its on all the plugs.

CAM67152
cam67152 is offline  
Old 12-02-2009, 11:25 PM
  #4  
cepx111
Senior Member
RACING JUNKIE
 
Join Date: May 2006
Posts: 2,044
Default

Just curious what is the ambient air temp in your area?

Cool moisture ladden air will condensate on metal, especially this time of year.

It might be what your seeing.

Run the motor till you get it good and warm 180/200ish, let it cool till you can work on it without getting burned - then check the plugs.
That's what I do.

Cp
cepx111 is offline  
Old 12-03-2009, 04:26 AM
  #5  
itsabird
Senior Member
RACING JUNKIE
 
Join Date: Dec 2007
Location: ohio
Posts: 816
Default

if all looks well... no water in the oil, not over heating, then i agree with cepx, cold weather condensation.
itsabird is offline  
Old 12-03-2009, 04:34 AM
  #6  
cam67152
Senior Member
MASTER BUILDER
Thread Starter
 
Join Date: Apr 2009
Location: B.C. Canada
Posts: 145
Default

I'll try that this afternoon. Temps have been quiet cool, just above freezing, and wet!
cam67152 is offline  
Old 12-03-2009, 06:16 AM
  #7  
TheYellaBrick
Senior Member
RACING JUNKIE
 
TheYellaBrick's Avatar
 
Join Date: Mar 2008
Location: Emmett, Idaho
Posts: 7,334
Default

Originally Posted by cam67152
I'll try that this afternoon. Temps have been quiet cool, just above freezing, and wet!
THIS will be the issue ! Let 'er get up to temp and I'll bet you'll NOT find H20 on those sparkers.
TheYellaBrick is offline  
Old 12-03-2009, 08:33 AM
  #8  
BEAST477
Senior Member
RACING JUNKIE
 
BEAST477's Avatar
 
Join Date: Feb 2007
Location: Michigan
Posts: 1,900
Default

Huh, I thought thats what I said, kinda. Now I'm confused.
BEAST477 is offline  
Old 12-03-2009, 10:13 AM
  #9  
itsabird
Senior Member
RACING JUNKIE
 
Join Date: Dec 2007
Location: ohio
Posts: 816
Default

Originally Posted by BEAST477
Huh, I thought thats what I said, kinda. Now I'm confused.
yes you did, about the valve cover condesation, i had a guy tell, that hanging light bulb, or shrouded shop light over the engine would cure the problem.
itsabird is offline  
Old 12-03-2009, 01:08 PM
  #10  
TheYellaBrick
Senior Member
RACING JUNKIE
 
TheYellaBrick's Avatar
 
Join Date: Mar 2008
Location: Emmett, Idaho
Posts: 7,334
Default

Beast,
Us old guys kinda rererepeat stuff, dontchya know :shock:
:roll: ops: ops:
TheYellaBrick is offline  

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -