Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: finished my buddies sbc!

  1. #1
    Senior Member EXPERT BUILDER
    Join Date
    Nov 2008
    Posts
    263

    finished my buddies sbc!

    ok so weve been workin on this 350 sbc .060 over for about 5 months now and we're finally done
    its got a scat all forged rotating assembly, forged flat tops, and afr alluminum heads 210 cc runner and 205int and 160exh valves, harland sharp 1.5 rockers and a lunati 525int and 540exh cam, air gap manifold and 750 carb
    hes wantin a few guesses on power, i said close to 525 give or take
    what do yall think?

  2. #2
    Senior Member RACING JUNKIE
    Join Date
    Dec 2004
    Location
    austin texas
    Posts
    729
    5 months? its hard enough to keep a motor clean for 2 hours while assembling....lol

    Good job, i hope it works out well for you 2

  3. #3
    Senior Member RACING JUNKIE
    Join Date
    Sep 2007
    Posts
    4,143

    Re: finished my buddies sbc!

    Quote Originally Posted by bowhay
    hes wantin a few guesses on power, i said close to 525 give or take
    what do yall think?
    I think yall was smoking weed.

    That things good for at least 600...maybe 625.

  4. #4
    Senior Member RACING JUNKIE
    Join Date
    Sep 2007
    Location
    orland pk il
    Posts
    2,429
    CHASIN WOMEN AND DRINKIN HOT TEXAS BEER AGAIN :roll:

  5. #5
    Senior Member RACING JUNKIE
    Join Date
    Dec 2004
    Location
    austin texas
    Posts
    729
    :roll:

  6. #6
    Senior Member RACING JUNKIE
    Join Date
    Sep 2007
    Location
    Belleville, IL
    Posts
    658

    Re: finished my buddies sbc!

    Quote Originally Posted by Tod74
    Quote Originally Posted by bowhay
    hes wantin a few guesses on power, i said close to 525 give or take
    what do yall think?
    I think yall was smoking weed.

    That things good for at least 600...maybe 625.
    You mean all low compression, small cammed, 350 chevy's don't make 1.5 HP/CID???

    Dammit! :shock:
    -WJ Birmingham

    OneBadGMC.com

  7. #7
    Senior Member RACING JUNKIE
    Join Date
    May 2006
    Posts
    2,044
    With the low compression and the limiting intake> I'd say maybe 450HP-500 tops.
    ***IN GOD WE TRUST***

  8. #8
    Senior Member EXPERT BUILDER
    Join Date
    Jan 2005
    Posts
    336
    u need to tell more info on cam(solid or hydraulic then roller or flattappet)
    also what is compression ratio?

    off top of my head ill guess 450 would be doing pretty well if 10:1 compression hydraulic flat tappet....tell us more!!!


    by the way the intake is fine unless u regularly take er up to 7000 rpms or higher

  9. #9
    Senior Member EXPERT BUILDER
    Join Date
    Nov 2008
    Posts
    263
    hydrolic flat tappet, with a 10.5 to 1

  10. #10
    Senior Member RACING JUNKIE
    Join Date
    Sep 2007
    Location
    orland pk il
    Posts
    2,429
    I WOULD AGREE WITH RUSS67CHEVELLE 450-475


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Copyright © 2005-2016 RacingJunk.com All Rights Reserved.

Designated trademarks and brands are the property of their respective owners. Use of this Web site constitutes acceptance of the RacingJunk.com
Terms of Use, Classifieds Disclaimer, Privacy Policy, and Cookie Policy