Groden Aluminum Rods
#2
Groden rods
Here are some posts from Yellow Bullet.
There are quite a few comments.
Some are just classifieds.
Hope this helps.
http://www.yellowbullet.com/forum/se...archid=3044129
There are quite a few comments.
Some are just classifieds.
Hope this helps.
http://www.yellowbullet.com/forum/se...archid=3044129
#4
Senior Member
RACING JUNKIE
Join Date: Sep 2007
Location: Belleville, IL
Posts: 658
Ash;
If you don't already have rods, I'd recommend MGPs. They're what I used in my most recent motor.
http://www.mgpconnectingrods.com/products.htm
I'm using the BBC6500 series with a 1.094 pin.
If you don't already have rods, I'd recommend MGPs. They're what I used in my most recent motor.
http://www.mgpconnectingrods.com/products.htm
I'm using the BBC6500 series with a 1.094 pin.
#5
Senior Member
RACING JUNKIE
Thread Starter
Join Date: Nov 2004
Location: St. Louis, Missouri
Posts: 661
Well, I just took new set of Groden's in on trade, I have used grp & mgp in the past. No problems with either one for drag strip applications. I use the oliver rod for street applications.
Just curiouis, They look like a nice set and the owner says he backs them up strip or street.... Yeah you heard me.......Street or Strip
The only thing I can say about using aluminum rods for daily drivers is a 1932 Boat Tail Bear Cat Stutz utilized aluminum rods. Not many of those cars made, but the one I know of is still running strong on its original build.
Just curiouis, They look like a nice set and the owner says he backs them up strip or street.... Yeah you heard me.......Street or Strip
The only thing I can say about using aluminum rods for daily drivers is a 1932 Boat Tail Bear Cat Stutz utilized aluminum rods. Not many of those cars made, but the one I know of is still running strong on its original build.
#7
Senior Member
RACING JUNKIE
Thread Starter
Join Date: Nov 2004
Location: St. Louis, Missouri
Posts: 661
groden, himself
I thought his claim was a little facious, myself.
Check out his web site
http://www.grodenracingrods.com/index.htm
Here is an excerpt from his web page
Our patented rod-to-cap design makes our rods the strongest in the world. In fact, our rods are over 30 % stronger than any rod on the market! Composed of space age billet aluminum, our rods are road tested to stand up to tomorrow’s heat and pressure engine performance standards.
At Groden Racing Rods we have eliminated rod failure with space age strength aluminum that allows no temperature growth. Throughout our rigorous engineering, testing and re-testing phases, our rods have unsurpassed quality control and craftsmanship, and are guaranteed not to have any forging flaws or cause distortion to the bores.
“The Rod with the Cap that snaps Right on”
I thought his claim was a little facious, myself.
Check out his web site
http://www.grodenracingrods.com/index.htm
Here is an excerpt from his web page
Our patented rod-to-cap design makes our rods the strongest in the world. In fact, our rods are over 30 % stronger than any rod on the market! Composed of space age billet aluminum, our rods are road tested to stand up to tomorrow’s heat and pressure engine performance standards.
At Groden Racing Rods we have eliminated rod failure with space age strength aluminum that allows no temperature growth. Throughout our rigorous engineering, testing and re-testing phases, our rods have unsurpassed quality control and craftsmanship, and are guaranteed not to have any forging flaws or cause distortion to the bores.
“The Rod with the Cap that snaps Right on”
#8
Senior Member
RACING JUNKIE
Join Date: Sep 2007
Location: Belleville, IL
Posts: 658
BME claims you can run their rods on the street too.
http://www.bmeltd.com/rods.htm
I sure as heck wouldn't try it.
http://www.bmeltd.com/rods.htm
Originally Posted by BME
The Only Streetable Aluminum Rod
Urban legends abound in the gearhead community. One is: aluminum connecting rods don't work in street engines. Prior to the mid-'70s, that might have been true, however, introduction of the Bill Miller Engineering Forged Aluminum Connecting Rod in 1975 provided an exception to that myth.
The BME Rod has good durability in high-end, high-power, street/strip or hot street engines because it is die-forged, rather than cut out of an aluminum plate. Bill Miller Engineering's unique, high-strength, aluminum alloy further enhances fatigue strength such that the potential durability of BME Rod rivals that of many forged steel rods and exceeds that of a few.
Urban legends abound in the gearhead community. One is: aluminum connecting rods don't work in street engines. Prior to the mid-'70s, that might have been true, however, introduction of the Bill Miller Engineering Forged Aluminum Connecting Rod in 1975 provided an exception to that myth.
The BME Rod has good durability in high-end, high-power, street/strip or hot street engines because it is die-forged, rather than cut out of an aluminum plate. Bill Miller Engineering's unique, high-strength, aluminum alloy further enhances fatigue strength such that the potential durability of BME Rod rivals that of many forged steel rods and exceeds that of a few.