Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Enderle cover

  1. #1
    Senior Member EXPERT BUILDER
    Join Date
    Mar 2003
    Posts
    337

    Enderle cover

    Does anyone know if Enderle makes a plate (or where to get one) for the timing cover to put where the fuel pump mounts? Mine is polished and looks nice (never mind pulling balancer and sealing everything back up) but, I want to change to a belt drive for the pump.

    Thanks for any help

  2. #2
    Senior Member RACING JUNKIE
    Join Date
    Mar 2003
    Location
    Fountain,MICHIGAN
    Posts
    856

    Plate

    If they Dont?
    I surely could whip you 1 up Fairly Resonable?
    Let me know?
    Later
    Greg 8)

  3. #3
    Senior Member EXPERT BUILDER
    Join Date
    Mar 2003
    Posts
    337
    bbchevy,
    could you make it in polished billet aluminum?
    What could we do about a cam button of some kind? any ideas?

  4. #4
    Senior Member RACING JUNKIE
    Join Date
    Mar 2003
    Location
    Fountain,MICHIGAN
    Posts
    856

    Cover

    It would be Alu.
    As for the POLISH,thats up to You......?
    I could be Made to the Depth of the Inner side of the Cover,then Shim the Button Accordingly!
    Later
    Greg 8)

  5. #5
    Senior Member EXPERT BUILDER
    Join Date
    Mar 2003
    Posts
    337
    OK, let me study on this a little bit.
    The thing is I still have the hex drive on the cam! I am not sure about a cam button with that still on there. Of course if I have to take it off, I will just put on a new cover. I did find out Enderle does not make one. (Maybe for that reason) Any suggestions?

  6. #6
    Senior Member RACING JUNKIE
    Join Date
    Dec 2004
    Location
    austin texas
    Posts
    729
    can you post a pic of what you hex drive looks like, it should have a bearing around it that limits cam end play to the cover?

  7. #7
    Senior Member EXPERT BUILDER
    Join Date
    Mar 2003
    Posts
    337
    Yea, I forgot about the torrington bearing on it until I pulled the pump off.
    I guess it would be the same as shimming to the pump extension.
    Thanks kwkracing!

    bbchevy do you have a cover to go by?

  8. #8
    Senior Member RACING JUNKIE
    Join Date
    Mar 2003
    Location
    Fountain,MICHIGAN
    Posts
    856

    cover

    I Have an Original WEIAND BBC Cover hanging here on the Wall.
    Later
    G 8)

  9. #9
    Senior Member EXPERT BUILDER
    Join Date
    Mar 2003
    Posts
    337
    I don't know if the covers are the same or not. Is it notched on the bottom of pump mount for the balancer? because the plate needs to be.
    let me see what I can find out.
    Took the pump and extension off and I see that the hex drive is almost flush with the outer cover. If my straight edge is right I have .016 between them, so we can just go flat with it. I'm sorry, I should have pulled that off before I started asking questions! ops:
    I'll see if I can find a pic of the weiand cover somewhere

  10. #10
    Senior Member RACING JUNKIE
    Join Date
    Mar 2003
    Location
    Fountain,MICHIGAN
    Posts
    856

    Cover

    N0 PR0BLEM!
    Just Hope that i can Help?
    These Guys on Here have been a GREAT Help to Me,so maybe i can do the same?
    Later
    G 8)

  11. Racing Junk


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Copyright © 2005-2016 RacingJunk.com All Rights Reserved.

Designated trademarks and brands are the property of their respective owners. Use of this Web site constitutes acceptance of the RacingJunk.com
Terms of Use, Classifieds Disclaimer, Privacy Policy, and Cookie Policy