bad cam

Old 03-04-2008, 06:38 PM
  #1  
bbc28racing
Junior Member
JOURNEYMAN
Thread Starter
 
Join Date: Feb 2008
Posts: 28
Default bad cam

i have a 454 and all my lifters stuck,so i put new ones in and ran one race and there already weak.when you ajust them the motor bogs down before the rockers stop rattling but.any ideas?thanks
bbc28racing is offline  
Old 03-04-2008, 07:13 PM
  #2  
a13badazztoys
Junior Member
APPRENTICE
 
Join Date: Sep 2007
Posts: 24
Default

Stuck?? what do you mean by stuck? :shock: siezed up ?? the engine should bog down a little when you adjust your hydrolic cam and its a little to far out of adjustment .. I assume hydrolic since you stated till the rockers stop rattling... any more info ?? solid cam ? roller ? cam lobes wiped out ?
a13badazztoys is offline  
Old 03-04-2008, 07:43 PM
  #3  
bbc28racing
Junior Member
JOURNEYMAN
Thread Starter
 
Join Date: Feb 2008
Posts: 28
Default

seized yes springs inside froze and quit oiling kindof like if the were solids,and new ones work good but now are starting to do it too the motor starts popping not loud popping like times too high and laboring almost dieing.can't set past .004 with feeler gauge hydrolic cam 490 like stock cam all stock lobes rockers and springs look good .maybe cams qround wrong :?: can't figure it out.help any?thanks
bbc28racing is offline  
Old 03-04-2008, 08:17 PM
  #4  
olds48
Senior Member
RACING JUNKIE
 
Join Date: Sep 2007
Location: Montvale, VA
Posts: 1,431
Default

Do you have roller rockers?They will always make a little rattling noise.Are you pushrods okay?Best way to set valves is with engine warm but not running.Get the valve your adjusting completely closed to the head,then tighten the nut untilyou just barely get rid of all your slack.Then put 1-1.5 turns of preload on it and walk away.
olds48 is offline  
Old 03-04-2008, 08:25 PM
  #5  
bbc28racing
Junior Member
JOURNEYMAN
Thread Starter
 
Join Date: Feb 2008
Posts: 28
Default

no rollors,push rods are good.that' how i usually ajust by bumping up the valves but it wont run.u can't even go a 1/4 a turn if u do it one at a time or the motor starts to die.tried it hot cold running not running .what could it be??thanks
bbc28racing is offline  
Old 03-04-2008, 08:34 PM
  #6  
olds48
Senior Member
RACING JUNKIE
 
Join Date: Sep 2007
Location: Montvale, VA
Posts: 1,431
Default

Did you put the cam in yourself?Is it a possibility that you got the timing set out of time,like one tooth off.I did that once,it sucked.I learned to slow down
olds48 is offline  
Old 03-04-2008, 08:39 PM
  #7  
bbc28racing
Junior Member
JOURNEYMAN
Thread Starter
 
Join Date: Feb 2008
Posts: 28
Default

that makes sense,definety will check it.thanks
bbc28racing is offline  
Old 03-04-2008, 08:46 PM
  #8  
olds48
Senior Member
RACING JUNKIE
 
Join Date: Sep 2007
Location: Montvale, VA
Posts: 1,431
Default

Can't think of anything else off the top of my head. Let us know what you find
olds48 is offline  
Old 03-04-2008, 09:20 PM
  #9  
SST4530
Senior Member
DYNO TECH
 
Join Date: Feb 2004
Location: Leonard, Texas
Posts: 414
Default

I thnik 1 1/2 turns is to much on the lifter adjustment. 1/2 to 3/4 turn should be plenty to put plunger in center of lifter.
SST4530 is offline  
Old 03-04-2008, 09:36 PM
  #10  
bbc28racing
Junior Member
JOURNEYMAN
Thread Starter
 
Join Date: Feb 2008
Posts: 28
Default

yes but,i can't even turn them a 1/4 it won't run if i go 1/2 usually would set on tight 1/4
bbc28racing is offline  

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -