Where Can I Find A BBC to SBC Front Adapter Motor Plate.

Old 01-13-2008, 02:17 AM
  #1  
dragraceme
Junior Member
SHOW GUEST
Thread Starter
 
Join Date: Oct 2006
Posts: 2
Default Where Can I Find A BBC to SBC Front Adapter Motor Plate.

Where Can I Find A BBC to SBC Front Adapter Motor Plate.

Like The One In The Picture See Ad #1080656
dragraceme is offline  
Old 01-13-2008, 03:35 AM
  #2  
johnracer
Senior Member
DYNO OPERATOR
 
Join Date: Aug 2005
Location: Rifle Colorado
Posts: 585
Default

You'll probably have to get one made for you. I fabricated spacers to go between the rear of the big block tabs on the chassis and the front of a straight small block motor plate. Looked and worked fine. I can email you a pic or I'll post it here if someone can tell me how....
johnracer is offline  
Old 01-13-2008, 03:43 AM
  #3  
dragraceme
Junior Member
SHOW GUEST
Thread Starter
 
Join Date: Oct 2006
Posts: 2
Default

You can email me a pic. to [email protected]


Originally Posted by johnracer
You'll probably have to get one made for you. I fabricated spacers to go between the rear of the big block tabs on the chassis and the front of a straight small block motor plate. Looked and worked fine. I can email you a pic or I'll post it here if someone can tell me how....
dragraceme is offline  
Old 01-13-2008, 04:31 AM
  #4  
johnracer
Senior Member
DYNO OPERATOR
 
Join Date: Aug 2005
Location: Rifle Colorado
Posts: 585
Default

Email sent....
johnracer is offline  
Old 01-13-2008, 06:48 AM
  #5  
edvancedengines
Senior Member
DYNO OPERATOR
 
Join Date: Feb 2006
Location: VA Hospital, Dallas, Tx (214 302 1924) cell-972-464-7400
Posts: 540
Default

Any sheet metal shop shoul;d be able to fab that up from scratch for you. It shouldn't be that big of a deal. Just tell them how much of a Z you need on it.

You can also buy a semi-finished SB Plate for a wider frame than you have and get the sheet metal shop to just make it to be offset like the one you want. You are just talking about 4 bends at a 45 deg angle. Then fit the rest to your car. It does look cool though.

Ed
edvancedengines is offline  
Old 01-13-2008, 09:55 AM
  #6  
gnsrule
Senior Member
SENIOR BUILDER
 
Join Date: Nov 2004
Posts: 118
Default

This should set you up right:
http://www.quartermax.com/details.ph...1056&catID=192
gnsrule is offline  
Old 01-13-2008, 11:17 AM
  #7  
jmarksdragster
Senior Member
RACING JUNKIE
 
jmarksdragster's Avatar
 
Join Date: Jul 2007
Location: Florida
Posts: 635
Default

Tommy makes the motor plates you need, as well other stuff like trans shields.
http://www.racecarpartsdepot.com/tra...n-shields.html
jmarksdragster is offline  
Old 01-13-2008, 07:33 PM
  #8  
Racefab57
Senior Member
DYNO OPERATOR
 
Join Date: Nov 2006
Location: NC
Posts: 557
Default

Suncoast racecars has em.David.
Racefab57 is offline  
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -