TH-400 HELP !!!!

Old 08-27-2007, 09:16 AM
  #1  
CHEVYZ28
Junior Member
SHOW GUEST
Thread Starter
 
Join Date: Aug 2007
Posts: 4
Default TH-400 HELP !!!!

Overhauled a B&M Racing TH-400, full manual, transbrake, reverse pattern.

I am missing the right possition of the ball that goes in the valve body (only one ball for this racing trans)

Anyone that could help me find the right possition of that ball?

Thanks,

Oliver
CHEVYZ28 is offline  
Old 08-27-2007, 05:30 PM
  #2  
jbsjunk
Senior Member
EXPERT BUILDER
 
Join Date: Apr 2004
Posts: 279
Default

Could try here http://www.bmracing.com/forum/default.asp

The source is the best place to start.
jbsjunk is offline  
Old 08-28-2007, 10:14 AM
  #3  
CHEVYZ28
Junior Member
SHOW GUEST
Thread Starter
 
Join Date: Aug 2007
Posts: 4
Default

Originally Posted by jbsjunk
Could try here http://www.bmracing.com/forum/default.asp

The source is the best place to start.
Thanks, I already did. By the way, called B&M in California and they do not want to tell me. Do not want to give or sell me installation instructions on the overhaul kit(which I bought from Summit).

Can not send the tranny to a shop in USA as I am located in Panama, Central America. It would be cheaper to buy a new one than sending it to the states and back to Panama.

Thanks,

Oliver
CHEVYZ28 is offline  
Old 08-28-2007, 03:57 PM
  #4  
jbsjunk
Senior Member
EXPERT BUILDER
 
Join Date: Apr 2004
Posts: 279
Default

Geesh! Talk about customer support......... :evil:

I know there are a few good trans guys here, they'll show up soon enough.
jbsjunk is offline  
Old 08-28-2007, 06:15 PM
  #5  
CHEVYZ28
Junior Member
SHOW GUEST
Thread Starter
 
Join Date: Aug 2007
Posts: 4
Default

Originally Posted by jbsjunk
Geesh! Talk about customer support......... :evil:

I know there are a few good trans guys here, they'll show up soon enough.
Hope they do show.

TKs

Oliver
CHEVYZ28 is offline  
Old 08-28-2007, 08:55 PM
  #6  
topsportsman1
Administrator
RACING JUNKIE
 
Join Date: Mar 2004
Location: Maine,USA
Posts: 1,204
Default

You can try here http://www.yellowbullet.com/forum/forumdisplay.php?f=30

Hutch is a good man on trannys,one of the best in the country.
I have also asked Hutch to join us,hope he does.

Tom
__________________
There Is 1 Thing Better Than Cubic Inches,,,More Of Them
topsportsman1 is offline  
Old 08-28-2007, 10:13 PM
  #7  
Hutchtrans
Junior Member
SHOW GUEST
 
Join Date: Aug 2007
Posts: 5
Default Re: TH-400 HELP !!!!

Originally Posted by CHEVYZ28
Overhauled a B&M Racing TH-400, full manual, transbrake, reverse pattern.

I am missing the right possition of the ball that goes in the valve body (only one ball for this racing trans)

Anyone that could help me find the right possition of that ball?

Thanks,

Oliver
The ball goes in the valve body close to the manual valve in a small pocket that should have a small coil spring wedged into it. If you look at the separator plate there will be a hole above where the ball goes into the valve body that is approx .155" dia.

Hope this helps, Hutch
Hutchtrans is offline  
Old 08-28-2007, 10:52 PM
  #8  
topsportsman1
Administrator
RACING JUNKIE
 
Join Date: Mar 2004
Location: Maine,USA
Posts: 1,204
Default

Thanks for stopping by Hutch and joining us here a RJ.

Lets all welcome Hutch,If you have any questions just ask Hutch,he's the man
__________________
There Is 1 Thing Better Than Cubic Inches,,,More Of Them
topsportsman1 is offline  
Old 08-29-2007, 02:59 AM
  #9  
jbsjunk
Senior Member
EXPERT BUILDER
 
Join Date: Apr 2004
Posts: 279
Default

Howdy Hutch. Welcome aboard!

I gotta ask, do you know Starsky? :lol:
jbsjunk is offline  
Old 08-29-2007, 03:57 AM
  #10  
CHEVYZ28
Junior Member
SHOW GUEST
Thread Starter
 
Join Date: Aug 2007
Posts: 4
Default Re: TH-400 HELP !!!!

Originally Posted by Hutchtrans
Originally Posted by CHEVYZ28
Overhauled a B&M Racing TH-400, full manual, transbrake, reverse pattern.

I am missing the right possition of the ball that goes in the valve body (only one ball for this racing trans)

Anyone that could help me find the right possition of that ball?

Thanks,

Oliver
The ball goes in the valve body close to the manual valve in a small pocket that should have a small coil spring wedged into it. If you look at the separator plate there will be a hole above where the ball goes into the valve body that is approx .155" dia.

Hope this helps, Hutch
Many thanks for your answer Hutch. I'll try this.

Regards,

Oliver
CHEVYZ28 is offline  

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -