Search: Posts Made By: HUNTER39
Showing results 1 to 25 of 28
Search took 0.01 seconds.
Forum: Engine Tech
07-23-2008, 09:31 AM
Replies: 6
Views: 750
Posted By HUNTER39

ROD BOLTS

I changed bearings after rebuild and still have same noise and it's the same rotating assy that was in the block before rebuild but minus the noise, the only difference is the mechanical fuel pump
Forum: Engine Tech
07-23-2008, 07:24 AM
Replies: 6
Views: 750
Posted By HUNTER39

NOISE

Well to tell you the truth I am also confused. The noise sounds like a dead knock in bottom end but like I said we changed the bearings but old bearings were fine. The noise is noticable on trans...
Forum: Engine Tech
07-21-2008, 03:40 AM
Replies: 6
Views: 750
Posted By HUNTER39

ENGINE NOISE????????

I have an 87 350 sbc rebuilt since rebuild motor has knocking noise at 1-2 shift and 2-3 shift, if I apply a little pressure at idle, in park to the serp. belt knock can be heard. I have put new...
07-14-2008, 11:01 AM
Replies: 1
Views: 382
Posted By HUNTER39

FUEL PUMP?????

I am building a sbc 383 approx 600+or- and a pro fogger system. I need to know what size fuel pump to run. Would be greatful for any help?
Forum: Transmission
06-11-2008, 02:52 AM
Replies: 4
Views: 696
Posted By HUNTER39

CONVERTOR SIZE?

Can someone tell me the benefits or drawbacks from a smaller 8in compared to a 10in convertor?
06-10-2008, 02:37 AM
Replies: 4
Views: 582
Posted By HUNTER39

THANKS

Thanks for the help!
06-09-2008, 09:38 AM
Replies: 4
Views: 582
Posted By HUNTER39

POWER TO MANUEL STEERING

I have a 79 malibu that I would like to convert from power to manuel steering. No one can seem to tell me what box ect... I need to do this any help would be greatly appreciated. thanks
Forum: Electrical
03-28-2008, 01:56 AM
Replies: 5
Views: 783
Posted By HUNTER39

anybody????????

Anybody using summit ignition?? Do you like or dislike? :(
Forum: Electrical
03-27-2008, 02:20 AM
Replies: 5
Views: 783
Posted By HUNTER39

summit racing ignition?

Anyone have any input on summit's street-strip pro cd digitial ignition?
Forum: Engine Tech
03-27-2008, 02:17 AM
Replies: 4
Views: 461
Posted By HUNTER39

BALANCERS?

What is the benefit of a larger harmonic balancer? For a sbc internal balance what would you recomend?
Forum: Engine Tech
03-19-2008, 04:51 PM
Replies: 2
Views: 337
Posted By HUNTER39

ARP OIL PUMP STUD?

On a sbc what should I torque a arp oil pump stud at?
Forum: Engine Tech
03-18-2008, 11:13 AM
Replies: 4
Views: 562
Posted By HUNTER39

problem solved

in 87-88 they made a shallow groove pisto and the standard deep groove we have the shallow groove. Thanks for your input
Forum: Engine Tech
03-18-2008, 10:49 AM
Replies: 4
Views: 562
Posted By HUNTER39

ring gap

yes approx .025 oil ring gap
Forum: Engine Tech
03-18-2008, 08:38 AM
Replies: 4
Views: 562
Posted By HUNTER39

350 sbc ring problem???????

I am installing a new set of rings, standard bore, only thing different is that the cylinders was honed. I have used 2 different set of rings and the oil rings are to tight to fit in the bores....
Forum: Engine Tech
03-18-2008, 02:40 AM
Replies: 3
Views: 381
Posted By HUNTER39

383sbc rod clearance problem

I am building a 79 350 stroked to 383. On the 2,4,6,8 cyl there is approx 1/8 clearence between rod bolts and bottom of cyl bore. On 1,3,5,7 cyl the bolts hit( not a lot but they hit) I am using a...
Forum: Engine Tech
03-16-2008, 10:59 AM
Replies: 2
Views: 405
Posted By HUNTER39

SBC RING GAPS??

I am building a 383sbc this is my first time with file fit rings. Can someone give me some specs on ring gap.The motor will ba a nitrous motor. Thanks for you help.
Forum: Engine Tech
03-08-2008, 09:30 AM
Replies: 1
Views: 338
Posted By HUNTER39

RODS TO PISTONS??

I recently purchased a compustar speed pack w/ mahle pistons for a sbc.Can someone tell me if there is a certian way in which rod must be installed on pistons? Is there a front, back, left, right?? I...
02-09-2008, 11:12 AM
Replies: 3
Views: 836
Posted By HUNTER39

CARB??????

:? I am building a 383 chevy would like input on the size of carb. Some info 11to1 comp, 250 nitrous, hurricain intake, world heads professionally ported and polished and matched. 1.6 rockers

cam...
Forum: Engine Tech
02-01-2008, 01:46 AM
Replies: 6
Views: 791
Posted By HUNTER39

THANKS

Thanks for the input guys. :D
Forum: Engine Tech
01-31-2008, 03:38 AM
Replies: 6
Views: 791
Posted By HUNTER39

COMPSTAR ROTATING ASSY???

Anyone using these rotating assy? If so had any problems, likes, dislikes? getting ready to purchase rotating assy for 383 and would like some feedback. thanks
Forum: Engine Tech
01-30-2008, 03:30 PM
Replies: 4
Views: 746
Posted By HUNTER39

SHORT FILL SBC

I am building a 383 chevy 600+hp and 250 shot block has been completely gone over and 4 bolt main and machined for main straps. My question is do I need to short fill the block and how do I go about...
01-24-2008, 03:11 AM
Replies: 8
Views: 1,142
Posted By HUNTER39

dual plate systems??

Is it possible to run two plate systems? 1st stage 125hp, 2nd stage 250hp. I'm new ti the nos thing so any input would be great. Thanks
01-18-2008, 08:45 AM
Replies: 20
Views: 2,073
Posted By HUNTER39

FINALLY RECIEVED

RECIEVED MY PART TODAY ALTHOUGH IT WAS NOT SHIPPED UNTIL YESTERDAY.
01-17-2008, 07:49 AM
Replies: 20
Views: 2,073
Posted By HUNTER39

NO REPLY

It's been 13 days and stiil no part. After repeated messages still no tracking#, shipping method or any other response and to say the least my patience are wearing thin.
01-16-2008, 02:43 PM
Replies: 20
Views: 2,073
Posted By HUNTER39

COMPLAINT

If your refering to my complaint it took 2 days for him to get his money from pa to ohio. I do have return slip. You can say what you want but theres no way it takes 15+ days for it to ship that far...
Showing results 1 to 25 of 28
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -