Search: Posts Made By: superstreeter
Showing results 1 to 25 of 122
Search took 0.02 seconds.
Forum: Engine Tech
03-04-2011, 05:06 AM
Replies: 3
Views: 890
Posted By superstreeter

Thanx Zip. I just noticed that. lol. I like your...

Thanx Zip. I just noticed that. lol. I like your #s . I'm thinkin of runnin 034 / 036
Forum: Engine Tech
03-03-2011, 01:13 PM
Replies: 3
Views: 890
Posted By superstreeter

piston ring end gap ?

What is everyone running for end gap, I'm going 540 bbc, with the odd spray of 250. conventional rings. running on pump gas. street / strip.. manufacturer says ..008 x bore for top ring, and .0055 x...
Forum: Engine Tech
02-19-2011, 04:26 PM
Replies: 8
Views: 2,144
Posted By superstreeter

OK one more thing on my mind here, ... I'm...

OK one more thing on my mind here, ... I'm measuring piston to head...I have .005 out of the hole...do I leave .040 clearance from there ?....or do I measure from the height of the piston rock,...
Forum: Engine Tech
02-17-2011, 03:57 PM
Replies: 8
Views: 2,144
Posted By superstreeter

Well I guess just for curiosity, I will measure...

Well I guess just for curiosity, I will measure the assembly, and see if the rest is out of wack, but as it stands,,,I'm .014 out of the hole, with the deck cleaned up about .004...never the...
Forum: Engine Tech
02-17-2011, 05:40 AM
Replies: 8
Views: 2,144
Posted By superstreeter

Thanx Zip I was looking for some specs like...

Thanx Zip
I was looking for some specs like that on the Dart block, I thought the deck height should be taller, mine specs out at 10.195. and I still have to clean 3-4 thou off.which leaves my combo...
Forum: Engine Tech
02-15-2011, 06:44 PM
Replies: 8
Views: 2,144
Posted By superstreeter

Dart bbc tall deck blocks

I need some quick info.....how tall are these blocks..I have a combo thats 10.205 tall..will I have room to clean the deck..Are they taller than 10.20...maybe 10.21 ?
Forum: Engine Tech
01-27-2011, 03:25 PM
Replies: 7
Views: 3,218
Posted By superstreeter

1st of all, before you get started with any...

1st of all, before you get started with any parts, you want to purchase, first figure out how fast you want to run, then build it acordingly. you will save yourself alot of money,switching parts back...
Forum: Engine Tech
01-25-2011, 06:10 PM
Replies: 28
Views: 3,836
Posted By superstreeter

your going to need about 650 hp

your going to need about 650 hp
01-22-2011, 12:02 PM
Replies: 8
Views: 732
Posted By superstreeter

NHRA in Big cucu

So I hear the NHRA is in big trouble with the IRS, were will the racers go now ??
Forum: Engine Tech
01-19-2011, 05:28 PM
Replies: 34
Views: 2,465
Posted By superstreeter

Part of that could all be in the convertor.....

Part of that could all be in the convertor.....
Forum: Transmission
01-04-2011, 06:55 PM
Replies: 0
Views: 412
Posted By superstreeter

ringless input shafts for p/glide

has anyone had problems with the new ringless input shafts not sealing, just what would happen if the shaft does not seal. ? the old ones had sealing rings, just wondering how the tranny would react...
Forum: In The Pits
12-27-2010, 12:04 PM
Replies: 1
Views: 512
Posted By superstreeter

Mufflers any idea ?

I need some feedback, and I guess I'll post it here. I need new 3 1/2 muffs for the street/strip buggy. 700hp. blew up the dynamax's flow through ones. I was going to try the spin tech. has anyone...
Forum: Engine Tech
12-24-2010, 02:33 PM
Replies: 13
Views: 3,311
Posted By superstreeter

Uhhhhhhhhhhh, thats going to be a pretty long...

Uhhhhhhhhhhh, thats going to be a pretty long belt, any chance of movin that alt. any closer ?
Forum: Engine Tech
12-08-2010, 04:03 PM
Replies: 9
Views: 1,299
Posted By superstreeter

4.600 bore, and a 4.5" stroke is what you...

4.600 bore, and a 4.5" stroke is what you probably have. a good set of heads and a decent cam, you'll get close to the 900hp, just make sure you look at the rest of your combo behind the crank. If...
Forum: Engine Tech
12-07-2010, 05:49 PM
Replies: 12
Views: 3,172
Posted By superstreeter

Yup, got all the junk on these now,,,T&D, or the...

Yup, got all the junk on these now,,,T&D, or the Jesel seem to be good, and they both make a sportsman set and a pro set, and they all have to be shimmed to get correct,,,,not too keen on the...
Forum: Engine Tech
12-07-2010, 05:40 PM
Replies: 9
Views: 1,299
Posted By superstreeter

598

I just tore a 588 apart, made 825 on a mild cam, a flat top will give you over 10 - 1 if you get a cam with the right valve timing to keep the compression up. I might add I ran pump gas to make the...
Forum: Engine Tech
11-29-2010, 06:55 PM
Replies: 12
Views: 3,172
Posted By superstreeter

No machining to mount the single bar ? Jesel has...

No machining to mount the single bar ? Jesel has the single bar too, but you have to machine the head to fit it.. T&D must have a couple of diffent models..
Forum: Engine Tech
11-29-2010, 06:08 PM
Replies: 12
Views: 3,172
Posted By superstreeter

I talked to an engine builder here about the T&D...

I talked to an engine builder here about the T&D shaft rockers, and he showed me a set mounted on a BBC, they have to be pinned to the heads or they may spin, then you`ve got problems. lol. so how...
Forum: Engine Tech
11-28-2010, 02:27 PM
Replies: 6
Views: 956
Posted By superstreeter

I was thinking of doing just that, after seeing a...

I was thinking of doing just that, after seeing a buddys stuff, but its good for a full race application, now that I`ve looked into it, if you want the full effect of the power you can build, and its...
Forum: Engine Tech
11-28-2010, 08:35 AM
Replies: 12
Views: 3,172
Posted By superstreeter

BBC Shaft rockers

need some info on the T&D rockers. Do they need any machining to install (afr heads) Do they have aligning brackets like the Jesel ? I cant seem to find any good lit. on the T&D. AFR says the T&D fit...
Forum: Engine Tech
11-25-2010, 04:09 PM
Replies: 15
Views: 2,600
Posted By superstreeter

Yes I`m not to keen on the Comp stuff either, I...

Yes I`m not to keen on the Comp stuff either, I lost a set of lifters too. And comp screwed up a special grind for me a while ago, seems their getting to big, and a little bit sloppy...........I do...
Forum: Engine Tech
11-24-2010, 06:48 PM
Replies: 15
Views: 2,600
Posted By superstreeter

Thanx Guys............now those are the numbers I...

Thanx Guys............now those are the numbers I thought would work,,and having these second oppinions, just makes me feel a little better about going that route, I had picked two Lunati cams, and...
Forum: Engine Tech
11-23-2010, 07:30 PM
Replies: 15
Views: 2,600
Posted By superstreeter

Thanx, yours seems a little closer than what I...

Thanx, yours seems a little closer than what I got from the cam compamies, lets see what others think.........

and the 315 head flows a bit better at .400 lift than the 335 head
Forum: Engine Tech
11-23-2010, 06:38 PM
Replies: 15
Views: 2,600
Posted By superstreeter

OK convertor is a 4500, give or take a bit, I`m...

OK convertor is a 4500, give or take a bit, I`m looking for a power range of 3500 - 6800 , running pump gas, 1050 - 1250 dominator, (old carb is a 1250) I have a # in mind for a cam, but everyone...
Forum: Engine Tech
11-23-2010, 02:58 PM
Replies: 15
Views: 2,600
Posted By superstreeter

lets get everyones feedback

I`m building a 540 tall deck pump gas engine, I`m mainly looing for the right cam to use, solid roller, I`m thinking :
700 HP and streetable
afr 315 cnc heads
10.2 - 1 comp mahle coated w/ small...
Showing results 1 to 25 of 122
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -