Search: Posts Made By: mikesramblur
Showing results 1 to 25 of 30
Search took 0.01 seconds.
07-14-2011, 01:33 PM
Replies: 4
Views: 1,018
Posted By mikesramblur

throttle body cleaner is a good thing. worked...

throttle body cleaner is a good thing. worked just fine and idles like new again. even took away a little stumble it had for a longtime.

thanks
07-13-2011, 01:45 AM
Replies: 4
Views: 1,018
Posted By mikesramblur

ok, i'll get some spray cleaner today and try...

ok, i'll get some spray cleaner today and try that tonite. try cheap first. had a look at the blades, their filthy black dirt on there.
07-12-2011, 03:52 PM
Replies: 4
Views: 1,018
Posted By mikesramblur

non racing related... 98 dakota problem

my dd 98 dakota 318 4x4. its been sitting for about 3 weeks, replaced battery on weekend and now wont idle. replaced tps twice. (first fell apart). didnt help. starts and runs fine but no idle....
06-20-2011, 05:46 PM
Replies: 4
Views: 804
Posted By mikesramblur

no return line used. no line into cell from...

no return line used. no line into cell from valve. there was no sloshing of fuel. its just been sitting, had it running a few times but didnt move the car. theres foam in the cell. i thought that...
06-20-2011, 02:23 PM
Replies: 4
Views: 804
Posted By mikesramblur

roll over valve leaking

This has been happening quite a bit since i installed it. Its on the top of the cell mounted in the hatch area of the car. its hosed through the floor to outside. Im finding gas on the garage floor....
03-14-2011, 02:14 PM
Replies: 6
Views: 1,542
Posted By mikesramblur

ok i does run when squirting gas into carb. but...

ok i does run when squirting gas into carb. but runs very rough then stops. i just found out the primary squirter is not working. secondary works great, and thats what i was looking at before. well...
03-14-2011, 02:22 AM
Replies: 6
Views: 1,542
Posted By mikesramblur

it cranks as usual. i checked that the rotor was...

it cranks as usual. i checked that the rotor was spinning when cranking. under cap is good.
im going to try some new gas in the carb tonite.
03-13-2011, 07:09 PM
Replies: 6
Views: 1,542
Posted By mikesramblur

:lol: nope. i didnt do that. means theres gas in...

:lol: nope. i didnt do that. means theres gas in the carb squirting into the ventures.
this is the fourth time today i heard that the gas is no good. ill give it a try this week.
keep ya posted.
03-13-2011, 05:11 AM
Replies: 6
Views: 1,542
Posted By mikesramblur

no start

Ive got a new hei ignition on an amc 360 that i seem to think might be a problem. its chev style ignition, coil in cap.
its always started and run fine. last week it decided to not start after...
04-09-2010, 04:00 AM
Replies: 9
Views: 1,649
Posted By mikesramblur

holley reccomendation needed

been talking to a few people on this and im getting all kinds of answers. i'm carb shopping now and undecided on mechanical or vacuum secondaries. i've had the vac carbs before and was thinking on...
Forum: Transmission
01-19-2010, 11:11 AM
Replies: 1
Views: 941
Posted By mikesramblur

manual valve body

when using a manual valve body do i still need to get a shift kit, or not required or its all included with vb?

this is for a 904.

thanks
01-19-2010, 10:56 AM
Replies: 3
Views: 997
Posted By mikesramblur

is that an abs plastic scoop you have? any pics...

is that an abs plastic scoop you have? any pics of it?
thanks
01-14-2010, 02:25 PM
Replies: 59
Views: 12,605
Posted By mikesramblur

if the springs are sagging so bad then replace...

if the springs are sagging so bad then replace them or add a leaf. bring it back to proper height then start. if you replace springs after everything is done your going to have all kinds of probs....
01-12-2010, 02:26 AM
Replies: 59
Views: 12,605
Posted By mikesramblur

what cam said.

what cam said.
01-11-2010, 05:43 AM
Replies: 59
Views: 12,605
Posted By mikesramblur

im working on a 79 spirit. no trunk. but i did...

im working on a 79 spirit. no trunk. but i did have to do some trimming near the frame to get the upper shock mount pipe in. i shoulda plated it before attaching to the frame but ....
i dont think...
01-09-2010, 06:31 AM
Replies: 3
Views: 997
Posted By mikesramblur

hood scoops

i bean looking at scoops, how does the abs plastic scoops attach? Are they not worth it, better off with fiberglass? Ive seen alot of fiberglass scoops cracking at the base where they attach.
01-09-2010, 03:34 AM
Replies: 59
Views: 12,605
Posted By mikesramblur

this should give you an idea. i couldnt get it...

this should give you an idea.
i couldnt get it high enough at the frame rails so move it forward enouth to take up the length of the bars. this is where it wanted to be so out comes the floor....
12-27-2009, 05:15 PM
Replies: 17
Views: 3,492
Posted By mikesramblur

ya it dont move at all now. thats the same thing...

ya it dont move at all now. thats the same thing i have in the pic. mine arent the link type tho.
nice truck, is it ready to run? whatcha got going on there where the shocks are supposed to be?
12-27-2009, 12:55 PM
Replies: 17
Views: 3,492
Posted By mikesramblur

its all good. changed tires and tightened up some...

its all good. changed tires and tightened up some bolts i forgot and its all tight now.
no need for a panhard bar.
thanks
12-27-2009, 08:01 AM
Replies: 17
Views: 3,492
Posted By mikesramblur

yup their bolt on type. car will be on the street...

yup their bolt on type. car will be on the street mostly other than garage art.
its sitting on lo aired slicks right now, so that might be the problem? i'll put the street tires on today and see if...
12-27-2009, 03:57 AM
Replies: 17
Views: 3,492
Posted By mikesramblur

anyone have pics of a panhard bar installed, just...

anyone have pics of a panhard bar installed, just want an idea of location on frame to where on the axle.
12-27-2009, 03:54 AM
Replies: 17
Views: 3,492
Posted By mikesramblur

is this the diagonal link you guys are talking...

is this the diagonal link you guys are talking about?
http://i87.photobucket.com/albums/k144/mikesamc/car003.jpg

if so its not stopping body movement on my car.
12-26-2009, 12:21 PM
Replies: 17
Views: 3,492
Posted By mikesramblur

alright then. thanks for in the info. i'll be...

alright then. thanks for in the info. i'll be looking for a panhard bar.
12-26-2009, 04:22 AM
Replies: 17
Views: 3,492
Posted By mikesramblur

ladder bar help

this has been a very long ongoing project getting this rearend done. i finally got it installed yesterday. its a ladderbar coil over suspension conversion on a leafspring car.
so, its all in tires...
06-30-2009, 03:14 PM
Replies: 10
Views: 2,779
Posted By mikesramblur

great thanks. thats what i want to hear. iread...

great thanks. thats what i want to hear. iread the directions and couldnt find anything that said this.
anyway heres some pics i just took. i will be using the washers....
Showing results 1 to 25 of 30
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -