Search: Posts Made By: ejm
Showing results 1 to 25 of 123
Search took 0.00 seconds.
Forum: Engine Tech
03-03-2015, 10:54 AM
Replies: 3
Views: 535
Posted By ejm

Thanks a bunch

Thanks a bunch
Forum: Engine Tech
03-02-2015, 08:27 PM
Replies: 3
Views: 535
Posted By ejm

bbc crank end play directions?

What's the best way to check crank end play on a bbc that will be in a pulling truck? And what's the correct cam end play also?
Forum: Engine Tech
03-19-2014, 05:38 PM
Replies: 1
Views: 647
Posted By ejm

Bbc valve adj with stud girdles

Just bought a motor solid roller cam moroso says to adj valves before installing the girdles can I set them before and then install girdles?
Forum: Engine Tech
03-02-2013, 01:12 AM
Replies: 0
Views: 248
Posted By ejm

bbc dual disc clutch longer pilot bushing/ bearing

im needing a pilot bearing that fits in the bigger part if the crank anyone know of a bearing that will fit with a sm 465 tranny? thanks in advance
Forum: Engine Tech
01-10-2013, 04:45 PM
Replies: 1
Views: 402
Posted By ejm

normal header temp bbc

k i know there are a bunch of factors on this subject but 11:1 bbc staight headers on pulling truck.I have a chance to get my headers powder coated but the high temp powder coat goes to 1200 degrees...
Forum: Engine Tech
10-14-2012, 04:20 PM
Replies: 30
Views: 3,689
Posted By ejm

was the last pull of the year and pulled great at...

was the last pull of the year and pulled great at 36* coolant temp only went up to 210 when last time it was at 225 but still header glow??
Forum: Engine Tech
10-03-2012, 06:25 AM
Replies: 30
Views: 3,689
Posted By ejm

Well only one more pull next weekend. It got up...

Well only one more pull next weekend. It got up to 220 which I didn't care for the carb came off of a 509 originally so I figure it wouldn't be lean. But if you say advancing would lean it out...
Forum: Engine Tech
10-02-2012, 10:43 AM
Replies: 30
Views: 3,689
Posted By ejm

first pull on this motor not really wanting to...

first pull on this motor not really wanting to turn more than7500 but it pulled it all the way down at the end
Forum: Engine Tech
10-02-2012, 08:06 AM
Replies: 30
Views: 3,689
Posted By ejm

Road kill you are exactly right if u think I...

Road kill you are exactly right if u think I should lock it I will no prob
110 oct msd 6al pro billet dist
Forum: Engine Tech
10-01-2012, 06:08 PM
Replies: 30
Views: 3,689
Posted By ejm

http://www.youtube.com/watch?v=W8EthyUDKZk&feature...

http://www.youtube.com/watch?v=W8EthyUDKZk&feature=plcp
this is the video not the best quality!
Forum: Engine Tech
10-01-2012, 06:06 PM
Replies: 30
Views: 3,689
Posted By ejm

dual disc clutch around 4000 4500 ease into it...

dual disc clutch around 4000 4500 ease into it four speed im gonna give a link to video
Forum: Engine Tech
10-01-2012, 05:54 PM
Replies: 30
Views: 3,689
Posted By ejm

maybe thats why when it "dogged" down at the end...

maybe thats why when it "dogged" down at the end it flat out almost died under 3000 rpm (dist not locked)
Forum: Engine Tech
10-01-2012, 03:53 PM
Replies: 30
Views: 3,689
Posted By ejm

I had total timing set at 30* think I should go...

I had total timing set at 30* think I should go higher?
Forum: Engine Tech
10-01-2012, 11:20 AM
Replies: 30
Views: 3,689
Posted By ejm

well got her going and wont really idle right and...

well got her going and wont really idle right and went down the track great but header glow at end of track any ideas
Forum: Engine Tech
09-29-2012, 11:42 AM
Replies: 30
Views: 3,689
Posted By ejm

yes they are ovl ports but with some work they...

yes they are ovl ports but with some work they will be fine builder was think they would have more torque at the end of the track so it wont fall on its face
Forum: Engine Tech
09-28-2012, 06:22 PM
Replies: 30
Views: 3,689
Posted By ejm

Stock heads but I can run a roller cam, which I...

Stock heads but I can run a roller cam, which I will do next year.
Forum: Engine Tech
09-28-2012, 03:17 PM
Replies: 30
Views: 3,689
Posted By ejm

Well it's not a drag motor and will never be...

Well it's not a drag motor and will never be consistant, its in a pulling truck and every track is different and the sled can be weighted differently as can the gearing it the weight box. So i was...
Forum: Engine Tech
09-27-2012, 02:45 PM
Replies: 30
Views: 3,689
Posted By ejm

duration 306 @.050 260 lobe sep 110*

duration 306 @.050 260 lobe sep 110*
Forum: Engine Tech
09-23-2012, 05:23 PM
Replies: 30
Views: 3,689
Posted By ejm

Bbc hp est

454 .040 over kb hyp pistons 11:1 Chevy 781 heads 2.19 in 1.72 ex bowls blended 629 lift solid flat tappet cam eagle forged crank stock rods all balanced Holley single plane intake and a demon 850
Forum: Engine Tech
09-19-2012, 04:29 PM
Replies: 4
Views: 1,063
Posted By ejm

what is the best way to set thrust bearings? have...

what is the best way to set thrust bearings? have all toqed and loosen rear cap pry back and then forward with crank then torque?
Forum: Engine Tech
09-16-2012, 09:38 AM
Replies: 4
Views: 1,063
Posted By ejm

yes they have arp rod bolts

yes they have arp rod bolts
Forum: Engine Tech
09-16-2012, 07:19 AM
Replies: 4
Views: 1,063
Posted By ejm

bearing clearances bbc

getting ready to put together 454 .040 over forged 4" crank factory rods (stess tested and ballanced) kb hyp 257 pistons 781's with 2.19 int valve bowl work and a .629 lift mech flat tappet wanting...
Forum: Engine Tech
08-26-2012, 06:34 PM
Replies: 5
Views: 966
Posted By ejm

with kb 257 pistons what compression will they...

with kb 257 pistons what compression will they yeild??
Forum: Engine Tech
08-26-2012, 06:32 PM
Replies: 5
Views: 966
Posted By ejm

bbc heads 049s or 781s???

going to put 2.19 intake valves in and some bowl work what heads will do better and have higher comp? so say 049s some times have a 122cc combustion chamber?????
Forum: Engine Tech
08-14-2012, 05:09 PM
Replies: 3
Views: 988
Posted By ejm

bbc rotating assembly

was going to up the hp in my bbc 460 what do you guys recomend as a rotating assembly looking to be in a street stock pulling truck but wanting to turn around 7000-7200 does a guy have to put forged...
Showing results 1 to 25 of 123
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service