Search: Posts Made By: kicker91laser
Showing results 1 to 25 of 37
Search took 0.01 seconds.
Forum: Transmission
01-22-2011, 08:59 AM
Replies: 0
Views: 535
Posted By kicker91laser

MW Accubond driveshaft on a street/strip application?

I was looking at using a 4" Bonded MMC Mark Williams drivehshaft on my next truck build, this will be a street/strip build, is there any reason that I should not use the bonded shafts? Fwiw, this is...
Forum: Transmission
10-09-2010, 09:03 AM
Replies: 3
Views: 538
Posted By kicker91laser

Thanks guys, I'll either have it cut or just...

Thanks guys, I'll either have it cut or just install this 12"converter to get the thing moveable. I'm not sure if I have enough clearance to shim the converter out.
Forum: Transmission
10-08-2010, 09:53 PM
Replies: 3
Views: 538
Posted By kicker91laser

GM Flexplate/converter issues??

I noticed the mounting bosses on my 10" converter hit the starter gear on my flexplate. The gear sticks out past the flexplate slightly so it would kinda bind and bend the flexplate itself if it...
04-11-2010, 04:24 AM
Replies: 3
Views: 1,076
Posted By kicker91laser

That's good to know, that is where I would be...

That's good to know, that is where I would be running it. I read in my NHRA rulebook, under general regulations, that the radiator must be mounted in stock location, this is why I was concerned.
04-10-2010, 06:41 PM
Replies: 3
Views: 1,076
Posted By kicker91laser

Rear mounted radiator in pickup truck-NHRA legal?

I am planning to run a rear-mounted radiator in my other turbocharged truck project. This will be a street/strip only truck, not building it for a particular class, just to run on test and tunes and...
04-05-2010, 08:57 PM
Replies: 3
Views: 2,321
Posted By kicker91laser

Mounting fuel cell in truck bed

Are there any specific ways to mount the cell in truck beds? I am going to run a rear sumped cell in my truck and was simply going to cut the recess out for the sump and strap it to the bed. Thanks...
12-17-2009, 07:57 AM
Replies: 5
Views: 639
Posted By kicker91laser

I do get Summit and Jegs, I'll look into them. ...

I do get Summit and Jegs, I'll look into them. Thanks Jim :)
12-16-2009, 07:22 PM
Replies: 5
Views: 639
Posted By kicker91laser

Thanks for the replies. Since I will be fabbing...

Thanks for the replies. Since I will be fabbing up my own motor mounts for this, is there an optimal angle that I should have the drivetrain at or will it all depend on ride height and pinion...
08-26-2009, 06:54 PM
Replies: 5
Views: 639
Posted By kicker91laser

Relocating engine back and lower

I will be relocating the engine in my turbo d50 pickup project back a few inches from stock location and lower it about an inch. With that said, I know moving the engine back will help weigh...
08-20-2009, 05:54 PM
Replies: 5
Views: 1,028
Posted By kicker91laser

Re: jig

I would, but I don't have access to a decent lathe anymore. :(
08-20-2009, 03:33 PM
Replies: 5
Views: 1,028
Posted By kicker91laser

Rear axle narrowing alignment jigs

Who all is now making these alignment jigs? Thanks guys.
08-04-2009, 04:31 AM
Replies: 2
Views: 516
Posted By kicker91laser

Re: ranger 8.8

That is what I was hoping to hear. Thank you.
08-03-2009, 04:54 AM
Replies: 2
Views: 516
Posted By kicker91laser

Ranger 8.8 rear end

Can the ranger 8.8 rear ends be upgraded just as the mustang 8.8(axles, carrier, diff cover)?
Forum: Transmission
07-26-2009, 07:22 PM
Replies: 17
Views: 7,006
Posted By kicker91laser

This is very good to know. Is it the 1-2 shift...

This is very good to know. Is it the 1-2 shift that cause the low sprag to fail? Is it ok to leave it in 1st just to clean the tires off?
Forum: Transmission
06-12-2009, 01:19 PM
Replies: 4
Views: 482
Posted By kicker91laser

Thanks zip, is it an acceptable practice to use...

Thanks zip, is it an acceptable practice to use offset dowel pins with the auto trans?
Forum: Transmission
06-11-2009, 08:28 PM
Replies: 4
Views: 482
Posted By kicker91laser

Acceptable offset between crank/trans input shaft

With all of the adapter bellhousings and plates, it seems that the crank and input shaft on the trans may not be perfectly centered with each other. That being said, what is an acceptable amount of...
Forum: Transmission
05-26-2009, 08:09 PM
Replies: 6
Views: 1,042
Posted By kicker91laser

who builds a good th400?

After talking with Marty Chance about my turbo 4 project, and posting on here, I have decided the th400 will work out well. That being said, who builds a good th400? Any suggestions are...
Forum: Transmission
05-17-2009, 09:24 AM
Replies: 17
Views: 4,479
Posted By kicker91laser

PG vs. th350/400 on the street

What is your opinions on a powerglide trans vs. a th350/400 trans on a street/strip car? Please discuss.

I know that the PG is recommended for the track, but how have you guys liked them on a...
Forum: Transmission
05-05-2009, 11:48 AM
Replies: 2
Views: 602
Posted By kicker91laser

th350 and 400

th350 and 400
Forum: Transmission
05-03-2009, 05:15 PM
Replies: 2
Views: 602
Posted By kicker91laser

Crank and input shaft runout tolerance?

How much runout between the crank and input shaft is allowable on a gm auto trans? Thanks guys.
Forum: Transmission
04-22-2009, 12:31 PM
Replies: 6
Views: 2,144
Posted By kicker91laser

TH350 rebuild-tips/special tools?

A friend and I are thinking about trying our hand at rebuilding some old th350s we have sitting around. I have picked up a Haynes gm trans repair manual already. Are there any tips and/or special...
Forum: Transmission
04-12-2009, 04:52 AM
Replies: 5
Views: 2,555
Posted By kicker91laser

Manually down-shifting a th350-good or bad?

I bought a th350 that has ~1k on a performance rebuild. On the receipt that came with the trans, it says not to down shift from 3rd. Is this a normal practice with these transmissions? I will be...
Forum: Transmission
04-11-2009, 04:29 AM
Replies: 5
Views: 580
Posted By kicker91laser

Does anyone make a modulator block-off to...

Does anyone make a modulator block-off to eliminate it?
04-07-2009, 05:09 PM
Replies: 0
Views: 494
Posted By kicker91laser

Setting up traction bars

I am going to make a set of traction bars for my truck(dodge d50). Is there an optimal location for the snubber to hit on the leaf springs and how much space should be between the leaf and snubber...
Forum: Transmission
03-19-2009, 09:41 PM
Replies: 2
Views: 412
Posted By kicker91laser

Converter stall on a turbocharged application

When selecting the stall speed, would it be best to have it right as the engine would come into boost, before, or well after it would be in boost? This is on a turbo 4 so it will not have alot of...
Showing results 1 to 25 of 37
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -