Search: Posts Made By: jed5161
Showing results 1 to 25 of 51
Search took 0.02 seconds.
Forum: Engine Tech
06-05-2011, 08:52 PM
Replies: 2
Views: 955
Posted By jed5161

i have a set of cnc 365's on my 605. they're a...

i have a set of cnc 365's on my 605. they're a little small for the cubic inch but its all i had when i build the bottom end. Main problem i have with them is the intake rocker stand bolt holes. Some...
Forum: Transmission
03-07-2011, 04:15 PM
Replies: 4
Views: 553
Posted By jed5161

Chance you could of broke the convertor. if thats...

Chance you could of broke the convertor. if thats the case it more than likely threw metal through the pump and all through the trans.

what size of engine are you running and how much hp you...
Forum: Transmission
03-06-2011, 08:26 PM
Replies: 4
Views: 553
Posted By jed5161

im guess'n blew up the forward (input) sprag

im guess'n blew up the forward (input) sprag
12-25-2010, 08:07 PM
Replies: 2
Views: 2,524
Posted By jed5161

yes pull the foam out of the tank....it will...

yes pull the foam out of the tank....it will disolve and plug up regulators and ruin pumps. as long as your running carb...yes tank in the rear is fine. if you ever go to injection you can make it...
12-21-2010, 08:17 PM
Replies: 6
Views: 3,091
Posted By jed5161

we have a sniper intake that was on both a 511...

we have a sniper intake that was on both a 511 cubic inch engine and a 605 inch engine. Using it with a rons injection on alcohol on both engines. Never really could get either motor to really take...
12-08-2010, 07:49 PM
Replies: 8
Views: 886
Posted By jed5161

had a super gas camaro doing simular...

had a super gas camaro doing simular thing....finally got to the point where it was swaying all the way down the track. Tore all the rear end suspension apart and found panhard tube bending under...
12-03-2010, 10:10 PM
Replies: 15
Views: 4,529
Posted By jed5161

go to rons direct....www.ronsfuel.com monroe...

go to rons direct....www.ronsfuel.com

monroe is only a "dealer". (kinda like biondo for digital delay.) i had my chance to deal with him (monroe) but choose not to for various reasons that are...
12-02-2010, 09:03 PM
Replies: 15
Views: 4,529
Posted By jed5161

just a matter of tuning (pump, pill, and nozzle...

just a matter of tuning (pump, pill, and nozzle sizes). i'd call ron's direct and they should have a baseline for your application.
Forum: Transmission
12-02-2010, 08:55 PM
Replies: 11
Views: 1,611
Posted By jed5161

what kind of trans fluid?

what kind of trans fluid?
06-11-2010, 08:39 PM
Replies: 2
Views: 695
Posted By jed5161

you refering to a nitrous "push" system? the CT...

you refering to a nitrous "push" system? the CT racing pro mods (Chuck, Jason, Chad Peterson's chevelles) ran this type of system when running their nitrous setup before switching to blower engines....
03-20-2010, 11:20 PM
Replies: 3
Views: 2,799
Posted By jed5161

mounting dragster front tires

what the best way to mount a new set of tires (22x2.5) on a set of weld wheels. wheels are anodized black so prying to stretch tire over wheel is out of the question.

second question....whats best...
Forum: Transmission
02-21-2010, 06:00 PM
Replies: 9
Views: 5,364
Posted By jed5161

B&M trick shift. we like the trick shift as it...

B&M trick shift. we like the trick shift as it has a higher boiling point and lubes better than regular dexron or type F. we ran 3-4 seasons without a transmission cooler on our 4 link dragster with...
Forum: Transmission
01-28-2010, 08:19 PM
Replies: 5
Views: 600
Posted By jed5161

from what i understand while being around a blown...

from what i understand while being around a blown pro mod which we ran for many years with an AFT clutch, the bronze insert will be more forgiving and will be more consistant than the steel. Once...
01-17-2010, 06:19 PM
Replies: 6
Views: 4,837
Posted By jed5161

car is right at 2000 with driver. we put the...

car is right at 2000 with driver. we put the mickey 33.5's back on the car. The hoosiers were not new. they were ran on our pro mod car for a short 6-8 race season and then our spitzer Pro Top Outlaw...
01-17-2010, 04:45 PM
Replies: 6
Views: 4,837
Posted By jed5161

we run all 1/8th mile exept for maybe two races a...

we run all 1/8th mile exept for maybe two races a year. (a 10k race and et finals) With 33.5's we do 140-142 mph. with 34.5's it fell off to 136-138 mph range. im not sure RPM wise what we do on the...
01-17-2010, 01:17 PM
Replies: 6
Views: 4,837
Posted By jed5161

4-link dragster rear gear ratio/tire size

Wondering what you guys out there are running for rear gear ratios and tire sizes. heres what i got:

250" 4 link dragster 1800 lbs
605 Ci BBC around 1050-1100 hp no bottle
1.80 glide
4.10...
01-17-2010, 01:06 PM
Replies: 5
Views: 1,190
Posted By jed5161

depends on the track conditions. If your on a...

depends on the track conditions. If your on a marginal track for your car & setup....yea it'll help you. If your on a track that super sticky...probably will hurt you. Either way it will slow you...
Forum: Transmission
11-29-2009, 01:14 PM
Replies: 6
Views: 5,238
Posted By jed5161

in theory just adding the overdrive ratio of .70...

in theory just adding the overdrive ratio of .70 you should be turning 2100 rpm. Thats without a lock up convertor clutch. if you add lock up i'll drop it about another 200-300 rpm, maybe a little...
Forum: Engine Tech
11-29-2009, 01:00 PM
Replies: 2
Views: 363
Posted By jed5161

the camshaft i have is from erson. its a...

the camshaft i have is from erson. its a hydraulic roller and has valve lift of .510/.510 and duration of 302/310 and card says 110+4 lobe center. gross lift is .340/.340 with duration at .050 being...
Forum: Engine Tech
11-28-2009, 11:57 PM
Replies: 2
Views: 363
Posted By jed5161

383 aftermarket tuned port camshaft

I have a GTA trans am that was a 355 small block with AFR cnc ported heads (187 cc port) with Tpis mini ram and 24 lb injectors. 9.5-10:1 right now. heres my cam specs off the web site......

ZZ-9...
Forum: Engine Tech
10-05-2009, 01:24 PM
Replies: 8
Views: 1,653
Posted By jed5161

from what i understand. gapless rings will...

from what i understand. gapless rings will "fludder". especially the middle ring due to pressure getting caught in between it and the top ring.
Forum: Engine Tech
07-31-2009, 01:26 PM
Replies: 2
Views: 420
Posted By jed5161

we just their "super pro" pump on our 604" BBC in...

we just their "super pro" pump on our 604" BBC in a fast bracket dragster. Seems be working great. Took around a tenth of et's. no more milky oil, no more oil leaks, etc. Only problem we had was...
Forum: Transmission
07-31-2009, 01:17 PM
Replies: 2
Views: 1,343
Posted By jed5161

http://www.ttcautomotive.com/English/products/T-56...

http://www.ttcautomotive.com/English/products/T-56.asp

heres the site for ratings and specs. high tq rated trans used the "viper" output shaft.
Forum: Transmission
07-05-2009, 08:55 PM
Replies: 11
Views: 1,546
Posted By jed5161

we did some testing with tractor hydraulic fluid...

we did some testing with tractor hydraulic fluid a few weeks ago. Thought it would lubricate the pump better. which it did a good job at that, problem was it was too slick and ate up a brand new race...
Forum: Transmission
06-17-2009, 08:25 PM
Replies: 6
Views: 755
Posted By jed5161

brake parts cleaner and compressed air. flush it...

brake parts cleaner and compressed air. flush it both ways until comes out clean. If has ALOT of metal or feels restricted at all when blowing through it, change it out. Best to have trans gone...
Showing results 1 to 25 of 51
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -