Search: Posts Made By: pipes434sbc
Showing results 1 to 11 of 11
Search took 0.00 seconds.
Forum: Engine Tech
10-26-2007, 04:47 PM
Replies: 39
Views: 6,871
Posted By pipes434sbc

good luck with whatever you decide gearhead,just...

good luck with whatever you decide gearhead,just so you know,I have a sollid roller 434,GM 4bolt block,deck plugs & cement.Run it on street like crazy,cleans up around town,never had a problem.Still...
Forum: Engine Tech
09-25-2007, 03:58 PM
Replies: 12
Views: 2,739
Posted By pipes434sbc

I thought I was a motorhead.Ed is a God.What an...

I thought I was a motorhead.Ed is a God.What an amazing piece of information,thanks.It all makes so much sense,specially the LS stuff. I have couple LS powered vehicles,so true.Thanks again Ed.
Forum: Engine Tech
09-20-2007, 06:54 PM
Replies: 14
Views: 1,265
Posted By pipes434sbc

thats what i run

thats what i run
Forum: Engine Tech
09-19-2007, 03:35 PM
Replies: 14
Views: 1,265
Posted By pipes434sbc

I run what comp cams refers to as "street solid...

I run what comp cams refers to as "street solid roller"in a 434sbc with ported 230cc heads.Works awsome.600 & change lift on a 108, yet not quite so aggressive of a ramp,allows a tighter lash(.018)&...
Forum: Engine Tech
09-18-2007, 04:05 PM
Replies: 11
Views: 941
Posted By pipes434sbc

I run a Meziere.its the most expensive,designed...

I run a Meziere.its the most expensive,designed for the street,55gph,& it is the best one out there.I have a cemented 434sbc ,drive on street,NEVER had an issue.(looks so cool to).It is so nice to be...
07-10-2007, 05:09 PM
Replies: 9
Views: 2,066
Posted By pipes434sbc

I had same problem with my ultra hp 950dbl pmp.I...

I had same problem with my ultra hp 950dbl pmp.I run a 434 with a solid roller on a 108.I run vacuum canister,and I drilled & tapped intake manifold just below rear bowl.I use a supervictor,& it...
Forum: Engine Tech
07-05-2007, 05:26 PM
Replies: 9
Views: 1,430
Posted By pipes434sbc

Hey Zano.Have to agree,do not just blow weights...

Hey Zano.Have to agree,do not just blow weights off,combined with the fact that your flexplate is bent,I would say replace it.Although I have blown weights off many 400 flywheels for 350 swaps with...
Forum: Transmission
07-04-2007, 04:29 PM
Replies: 16
Views: 12,057
Posted By pipes434sbc

p.s. (again) if you are asking this question,know...

p.s. (again) if you are asking this question,know this,the dampner on the front of this motor has to match as well.(internal external)The internals are smooth on outer edge. External usually grooved....
Forum: Transmission
07-04-2007, 04:16 PM
Replies: 16
Views: 12,057
Posted By pipes434sbc

Just about to eat dinner,but want to help.We had...

Just about to eat dinner,but want to help.We had our holiday july 1st.,guess yours is today.Is this motor internally balanced or external?Is flywheel new?,is it sfi approved?If it has weights on one...
Forum: Transmission
07-02-2007, 04:48 PM
Replies: 16
Views: 12,057
Posted By pipes434sbc

PS after opening holes on flywheel & bolts go in...

PS after opening holes on flywheel & bolts go in nice,make sure all 3 ears on converter are flush on flywheel the same.you might have to shim one or two or not.I have seen a few TCI`s with two ears...
Forum: Transmission
07-02-2007, 04:35 PM
Replies: 16
Views: 12,057
Posted By pipes434sbc

I had same problem with my new TCI conv.just open...

I had same problem with my new TCI conv.just open up the holes a tad with a die grinder or drill.(i used die grinder,keep as tight as possible.)I have many hours no problems.Actually my converter...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service