Search: Posts Made By: novassx
Showing results 1 to 11 of 11
Search took 0.01 seconds.
Forum: Engine Tech
01-16-2008, 11:22 AM
Replies: 2
Views: 1,119
Posted By novassx

Merlin 540 Main Bearing Clearance?

Just going to assemble my motor, Checked main bearing clearance and I have .004 on the mains. I am using a dial bore gauge to messure. Very reputable machine shop did the machine work, Line bore, who...
Forum: Transmission
05-24-2007, 11:58 AM
Replies: 3
Views: 1,024
Posted By novassx

I do not know much about powerglides, I do know...

I do not know much about powerglides, I do know there is all big dollar parts in this trans. Is the input shaft part of output shaft? Is this all 1 piece? It has a Vasco 1:80 straight cut gear...
Forum: Transmission
05-23-2007, 10:11 PM
Replies: 3
Views: 1,024
Posted By novassx

Speedo Options

Any suggestions for a speedo adapter. Would like to use the factory speedo in my 68 Camaro. My trans has a Deadenbear tailshaft housing with no provision for speedo cable and all internal components...
Forum: Transmission
05-23-2007, 09:53 PM
Replies: 1
Views: 1,173
Posted By novassx

Deadenbear case

When I bought my car it was a roller, It came with a drive shaft with a Mark Williams yoke. The trans I purchased has a Deadenbear case and tail shaft housing with roller bearing. The yoke is...
05-23-2007, 09:27 PM
Replies: 4
Views: 1,948
Posted By novassx

Sikkens makes a real nice semi gloss "Ralley...

Sikkens makes a real nice semi gloss "Ralley Black". It is a urethane. I used to use a flattening agent, mixed into acrylic enamel made by Dupont. Most make a semigloss black now. Ask for help on...
Forum: Electrical
05-19-2007, 08:25 AM
Replies: 19
Views: 2,637
Posted By novassx

I work at a GM dealership in service with 8...

I work at a GM dealership in service with 8 techs. The most comon is the fuel pump, then security system ( ignition switch), then the distibutor. Mostly fuel pumps will die, and car will not start...
Forum: Electrical
05-17-2007, 08:40 AM
Replies: 19
Views: 2,637
Posted By novassx

What you need to do, is to fool the system. You...

What you need to do, is to fool the system. You will need to find the resistance of your pellet key and install a resister of that value. There are 15 differant choises. Cut the 2 small wires at the...
Forum: Engine Tech
05-09-2007, 11:21 AM
Replies: 2
Views: 690
Posted By novassx

Yes it is hitting the pan where the cut out is....

Yes it is hitting the pan where the cut out is. And yes I am thinking I'll have to modifie the pan. Allthough I have not tried to move the block at starter yet. It said to used one of these starters....
05-08-2007, 11:34 PM
Replies: 20
Views: 2,654
Posted By novassx

Mufflers?

Great Post! I need to buy mufflers? My headers are 2 1/4" to a 4" collector, then I was thinking of a Flow Master Race muffler, 3 1/2 in/out and the body is 4". I'll put the muffler as far back as I...
05-08-2007, 11:19 PM
Replies: 29
Views: 3,595
Posted By novassx

Gas Milage?

Can anyone guess on gas milage with my 540 engine. Hoping to run it on the street in 2008. Still working on the 20 gal tank with some saddle tanks for the Cruise. LOL. 540 10.3 comp, 4:10's, 33'...
Forum: Engine Tech
05-08-2007, 10:54 PM
Replies: 2
Views: 690
Posted By novassx

Moroso Pro Eliminator Pan

I bought a CSR starter, It does not seem to fit my 540 block with this pan.

http://www.moroso.com/catalog/categorydisplay.asp?catcode=11341

This is the starter:...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -