Search: Posts Made By: montec468
Showing results 1 to 20 of 20
Search took 0.01 seconds.
04-26-2009, 04:32 PM
Replies: 0
Views: 459
Posted By montec468

Engine Builders

Does anyone know of a GOOD engine builder in or around the Minneapolis area? Thanks.
Forum: Engine Tech
01-23-2009, 04:35 PM
Replies: 9
Views: 717
Posted By montec468

Thanks Zip. I will look them up.

Thanks Zip. I will look them up.
Forum: Engine Tech
01-21-2009, 02:32 PM
Replies: 9
Views: 717
Posted By montec468

T&D dealers or distributors?

I have never bought a set of T&D rocker shafts before......is there dealers, distributors, or do I just call T&D?? Thanks.
04-24-2008, 10:38 AM
Replies: 4
Views: 833
Posted By montec468

Carb spacer recommendations

The last thing I need to purchase for my engine before I go to the dyno is a carb spacer. Currently I have the R.M. reversion spacer and a 1" spacer, but I believe there are better out there....
Forum: Transmission
04-23-2008, 05:45 PM
Replies: 7
Views: 1,442
Posted By montec468

I should of put on my previous post that I had...

I should of put on my previous post that I had just bought the alternator kit for my BBC and if I remember correctly it was 160 bucks. I did have the alternator and crank pulley in a V groove style...
Forum: Transmission
04-22-2008, 02:41 PM
Replies: 7
Views: 1,442
Posted By montec468

Is this something you are looking for? ...

Is this something you are looking for?

http://www.marchperf.com/pg63.html
04-16-2008, 04:19 PM
Replies: 7
Views: 1,696
Posted By montec468

My builder just got done with my motor today and...

My builder just got done with my motor today and about the last thing I have to buy is the carb spacer and I am at a little bit of a loss here. This motor has to sustain 7600-8000 rpm for 12-15...
Forum: Engine Tech
04-16-2008, 03:53 PM
Replies: 3
Views: 565
Posted By montec468

For those numbers you can use a GM 781 or 049...

For those numbers you can use a GM 781 or 049 head unless you want aluminum. I had 2 motors with a small solid flat tappet cam that made 550/550 on 92 octane with 2.19 & 1.88 valves without any...
Forum: Engine Tech
04-15-2008, 03:53 PM
Replies: 2
Views: 752
Posted By montec468

Vacuum Pump installation

I am putting on a Moroso 22641 vaccum pump on my 540 BBC and I have never run one before and I am not quite sure how to set it up with the regulator and such. Does anyone have photos they can post to...
Forum: Engine Tech
12-04-2007, 03:03 PM
Replies: 19
Views: 3,407
Posted By montec468

Did you use these 380 CNC heads? The reason I ask...

Did you use these 380 CNC heads? The reason I ask is that this is the first time I have seen these heads on their website. I did see a Dart 383 heads before on their website that were not CNC...
Forum: Engine Tech
12-04-2007, 01:19 PM
Replies: 19
Views: 3,407
Posted By montec468

I am not familiar with the Sniper Jr. Sorry I...

I am not familiar with the Sniper Jr. Sorry I don't know a whole lot about the Sniper products. Is the Sniper Jr. good out of the box or does it need to be worked over? Also, I was on Darts website...
Forum: Engine Tech
12-02-2007, 06:06 AM
Replies: 19
Views: 3,407
Posted By montec468

Sounds like a good comination you have. We are...

Sounds like a good comination you have. We are limited to a conventional heads. I have not been doing this for too long and I happen to get the 355 heads cheap from a friend of mine. I am trying to a...
Forum: Engine Tech
12-01-2007, 03:40 PM
Replies: 19
Views: 3,407
Posted By montec468

I have heard that Erson does a pretty good job...

I have heard that Erson does a pretty good job too. I am out in W.V. Are you an Outlaw puller or a brush puller guy?
Forum: Engine Tech
12-01-2007, 07:05 AM
Replies: 19
Views: 3,407
Posted By montec468

Thanks for all the help on this. Sorry, I guess I...

Thanks for all the help on this. Sorry, I guess I should of been more specific with my truck pulling motor. It is a 540 BBC 14.5:1 compression, Dart 355 cnc heads, Edelbrock Super Victor cnc ported...
Forum: Engine Tech
11-30-2007, 04:32 PM
Replies: 19
Views: 3,407
Posted By montec468

Need some help with ComCams, Lunati, LSM or camshaft profile

What I am looking for some help on who does the best camshaft profiles for my 540 BBC and has experience with various applications whether it is racing, pulling, or anything else. Thanks
Forum: Engine Tech
05-30-2007, 07:07 AM
Replies: 3
Views: 675
Posted By montec468

What's your cylinder bore?

What's your cylinder bore?
05-21-2007, 10:46 AM
Replies: 12
Views: 10,198
Posted By montec468

Slowman, I have since switched to Sunoco...

Slowman,

I have since switched to Sunoco Supreme 112 and I have been extremely pleased with the performance from it. The best part is that Sunoco is quite a bit cheaper than the VP fuels. :D
05-21-2007, 08:35 AM
Replies: 12
Views: 10,198
Posted By montec468

I have a 13.5:1 engine and when I dynoed my...

I have a 13.5:1 engine and when I dynoed my engine with C12 and C14, the C12 made 6.5 more HP @ 7300 RPM.
05-16-2007, 03:28 AM
Replies: 9
Views: 5,040
Posted By montec468

Thanks everyone for info. I brought my engine to...

Thanks everyone for info. I brought my engine to the dyno yesterday and ran the Sunoco Sumpreme 112 from last years barrel and it did well!!
05-14-2007, 03:56 PM
Replies: 9
Views: 5,040
Posted By montec468

How long does a 55 gallon barrel of fuel last

I have approximately 25 gallons of Sunoco Supreme 112 race fuel that is in a sealed 55 gallon steel drum and kept in the garage. Does the fuel loose octane or go bad since last season? Thanks. :D
Showing results 1 to 20 of 20


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -