Search: Posts Made By: rhiasdaddy
Showing results 1 to 25 of 26
Search took 0.02 seconds.
Forum: Electrical
01-16-2011, 06:10 PM
Replies: 2
Views: 512
Posted By rhiasdaddy

which system is better a 12volt or 16 volt

trying to figure which electrical system to run in my race truck so which is better 12 or 16
06-04-2009, 07:06 AM
Replies: 2
Views: 444
Posted By rhiasdaddy

mock up motor

i am lookin for a plastic mock up motor like they use on overhaulin any know where i can find one thanks rick
Forum: Engine Tech
05-25-2009, 09:35 AM
Replies: 25
Views: 1,435
Posted By rhiasdaddy

crank throw

how do u meassure the throw on a crank ?
Forum: Engine Tech
05-14-2009, 06:31 AM
Replies: 19
Views: 1,211
Posted By rhiasdaddy

it sounds like he just needs to junk it and start...

it sounds like he just needs to junk it and start over with a chevy product
Forum: Engine Tech
05-01-2009, 12:28 PM
Replies: 3
Views: 416
Posted By rhiasdaddy

engine math

can any one tell me the formula used in figureing c.u
Forum: Engine Tech
04-16-2009, 06:22 AM
Replies: 5
Views: 403
Posted By rhiasdaddy

my head swimming and confussed

first thanks to every one on here you all are good bunch of eggs . i understand that building a motor and what goes into it is almost a sceince with a whole lot of thought behind it . but for the...
Forum: Electrical
04-14-2009, 01:10 PM
Replies: 1
Views: 327
Posted By rhiasdaddy

magneto /distributor

which is better mag or distributor
Forum: Electrical
04-14-2009, 01:08 PM
Replies: 2
Views: 680
Posted By rhiasdaddy

delay box

what are the advantages /disadvantage to haveing a delay box ? do you half to have it to drag race
Forum: Engine Tech
04-14-2009, 01:03 PM
Replies: 6
Views: 338
Posted By rhiasdaddy

timeing chain or gear driven

which is better timeing chain or gear driven noisy off coarse
Forum: In The Pits
04-14-2009, 12:28 PM
Replies: 5
Views: 433
Posted By rhiasdaddy

oops sorry foregot about the wife .but cant...

oops sorry foregot about the wife .but cant aleays count on her to be here
Forum: In The Pits
04-14-2009, 12:27 PM
Replies: 5
Views: 433
Posted By rhiasdaddy

my prob is i dont really have and freinds that...

my prob is i dont really have and freinds that would come over and hang while i work on the race trk
Forum: Engine Tech
04-14-2009, 12:21 PM
Replies: 2
Views: 333
Posted By rhiasdaddy

piston rings

whats a good set of piston rings
Forum: Engine Tech
04-14-2009, 12:19 PM
Replies: 5
Views: 437
Posted By rhiasdaddy

crank shaft question

i have a stock steel crank shaft can i have it machined in to a stroker crank
Forum: Engine Tech
04-14-2009, 12:11 PM
Replies: 4
Views: 491
Posted By rhiasdaddy

whats the goin rate to have 454bbc heads done

i have stock 454 heads with 119 cc chambers rectangle ports i need to get them cleaned up and redone about how much ?i want all new put in to it
Forum: Engine Tech
04-14-2009, 12:03 PM
Replies: 10
Views: 1,104
Posted By rhiasdaddy

Re: bbcmotor work

so if i go 80 over that make it ?????? and how much does it coast to have machine work done ?
Forum: Engine Tech
04-14-2009, 11:59 AM
Replies: 10
Views: 1,104
Posted By rhiasdaddy

bbcmotor work

just checked the numbers on my block and it is a k block
Forum: Engine Tech
04-13-2009, 06:43 PM
Replies: 3
Views: 955
Posted By rhiasdaddy

wet sump/dry sump

can anyone tell me the advantages/disadvantages of wet sump /dry sump for drag racing
Forum: Engine Tech
04-13-2009, 05:48 PM
Replies: 6
Views: 843
Posted By rhiasdaddy

cast cyl heads

i want to use them for drag racing
Forum: Engine Tech
04-13-2009, 05:25 PM
Replies: 6
Views: 843
Posted By rhiasdaddy

cast cyl heads

i have a pair of cast bbc heads the are stamped hi performance should i have these heads reworked and dun up and use them or should i buy a set of aluminum heads ? i pulled the numbers and from what...
04-13-2009, 05:16 PM
Replies: 5
Views: 526
Posted By rhiasdaddy

rear gear choice

33x15 tire full tube chassis i want to run 1/8 and 1/4
Forum: Engine Tech
04-13-2009, 12:19 PM
Replies: 10
Views: 1,104
Posted By rhiasdaddy

bbc motor work?

i have a bbc 454 block it has never been bored .i want to bore it how big can i go with it ?
04-13-2009, 11:48 AM
Replies: 1
Views: 485
Posted By rhiasdaddy

tube bending

how do u determin how much tube u need before makin a bend
04-13-2009, 11:46 AM
Replies: 5
Views: 526
Posted By rhiasdaddy

rear gear choice

i am building a 92 chevy full size trk for the strip .i am goin with a 454 bbc with th400 trans i want to put a ford 9 in the rear but i dont know what gear to put in it any ideas
04-12-2009, 06:02 PM
Replies: 2
Views: 539
Posted By rhiasdaddy

rule book

how do i get a copy of the ihra an nhra rule book for buildin chassis
04-12-2009, 05:49 PM
Replies: 1
Views: 587
Posted By rhiasdaddy

what happens at nhra cert for chassis ?what do they do

i am building a full tube chassis for my 92 chevy 1500 8 foot bed what do they do at cert ?i am new to this and really dont know a hole lot about nhra inspections and cert i am learnin as i go so...
Showing results 1 to 25 of 26
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -