Racingjunk Forums

Racingjunk Forums (https://www.racingjunk.com/forums/index.php)
-   Transmission (https://www.racingjunk.com/forums/forumdisplay.php?f=14)
-   -   TH-400 HELP !!!! (https://www.racingjunk.com/forums/showthread.php?t=18199)

CHEVYZ28 08-27-2007 09:16 AM

TH-400 HELP !!!!
 
Overhauled a B&M Racing TH-400, full manual, transbrake, reverse pattern.

I am missing the right possition of the ball that goes in the valve body (only one ball for this racing trans)

Anyone that could help me find the right possition of that ball?

Thanks,

Oliver

jbsjunk 08-27-2007 05:30 PM

Could try here http://www.bmracing.com/forum/default.asp

The source is the best place to start.

CHEVYZ28 08-28-2007 10:14 AM


Originally Posted by jbsjunk
Could try here http://www.bmracing.com/forum/default.asp

The source is the best place to start.

Thanks, I already did. By the way, called B&M in California and they do not want to tell me. Do not want to give or sell me installation instructions on the overhaul kit(which I bought from Summit).

Can not send the tranny to a shop in USA as I am located in Panama, Central America. It would be cheaper to buy a new one than sending it to the states and back to Panama.

Thanks,

Oliver

jbsjunk 08-28-2007 03:57 PM

Geesh! Talk about customer support......... :evil:

I know there are a few good trans guys here, they'll show up soon enough.

CHEVYZ28 08-28-2007 06:15 PM


Originally Posted by jbsjunk
Geesh! Talk about customer support......... :evil:

I know there are a few good trans guys here, they'll show up soon enough.

Hope they do show.

TKs

Oliver

topsportsman1 08-28-2007 08:55 PM

You can try here http://www.yellowbullet.com/forum/forumdisplay.php?f=30

Hutch is a good man on trannys,one of the best in the country.
I have also asked Hutch to join us,hope he does.

Tom

Hutchtrans 08-28-2007 10:13 PM

Re: TH-400 HELP !!!!
 

Originally Posted by CHEVYZ28
Overhauled a B&M Racing TH-400, full manual, transbrake, reverse pattern.

I am missing the right possition of the ball that goes in the valve body (only one ball for this racing trans)

Anyone that could help me find the right possition of that ball?

Thanks,

Oliver

The ball goes in the valve body close to the manual valve in a small pocket that should have a small coil spring wedged into it. If you look at the separator plate there will be a hole above where the ball goes into the valve body that is approx .155" dia.

Hope this helps, Hutch

topsportsman1 08-28-2007 10:52 PM

Thanks for stopping by Hutch and joining us here a RJ.

Lets all welcome Hutch,If you have any questions just ask Hutch,he's the man

jbsjunk 08-29-2007 02:59 AM

Howdy Hutch. Welcome aboard!

I gotta ask, do you know Starsky? :lol:

CHEVYZ28 08-29-2007 03:57 AM

Re: TH-400 HELP !!!!
 

Originally Posted by Hutchtrans

Originally Posted by CHEVYZ28
Overhauled a B&M Racing TH-400, full manual, transbrake, reverse pattern.

I am missing the right possition of the ball that goes in the valve body (only one ball for this racing trans)

Anyone that could help me find the right possition of that ball?

Thanks,

Oliver

The ball goes in the valve body close to the manual valve in a small pocket that should have a small coil spring wedged into it. If you look at the separator plate there will be a hole above where the ball goes into the valve body that is approx .155" dia.

Hope this helps, Hutch

Many thanks for your answer Hutch. I'll try this.

Regards,

Oliver


All times are GMT -8. The time now is 04:00 AM.