Welcome to RacingJunk Classifieds, The World's #1 Motorsports Marketplace


3 comments


1 comment


0 comments


0 comments


0 comments


0 comments


0 comments


0 comments


1 comment


0 comments


0 comments


1 comment


1 comment

On the way here from Dr. Lockjaw's Shop in Oregon.
0 comments

Lightweight Drag frt clip will need some work.
0 comments

Still need to find a trunk lid, HELP
1 comment

Car being loaded at Dr.LockJaw's in Oregon. Friday the 13th....Hummm
0 comments

Loaded for the trip to Las Vegas at Gasserted's shop.
0 comments

I just received a box with magazines and pictures of the SS car. Drag Racing Magazine had a Center Fold picture of the car above with article. Also in two Hot Rod Magazines, one a Yearbook.
0 comments

Hot Rod Article October of 1967
0 comments

Drivers side Pivot and Front Clip Removal Pin
0 comments

Passinger side Pivot Pin to tilt frt clip forward, or pull pin's to remove frt clip from car.
1 comment

Halibrand 5 hole kidney bean spindle mount wheels
0 comments

This article will tell you a lot about what was in the car, even the spec's on the Racer Brown Cam. Great stuff for reviving an Original.
0 comments

Here is a good picture of the Blown Injected Late Model Hemi the Ernie and Tony Nancy built.
0 comments

Added rear body supports and removable rear bumper
0 comments

used the rear bumper mounts to support the rear of the body.
0 comments

had to put a larger nut for a spacer on rear body mounts to adj. trunk lid later...
0 comments

Rear bumper mouts are pinned to remove to take body off with 8 bolts.
0 comments

15X14 Cragers, wide as they make.
0 comments

Same +offset as the original wheels, but much wider.
0 comments

Crager custom made the wheels for the SS car.
1 comment

Ernie's Original Gasser Coupe
0 comments

I believe the front clip was made by Johnson Fiberglass Manufacturing
0 comments

Moon Fuel Tank
0 comments

Alignment of doors.
0 comments

Right door alignment
0 comments

Metal body, glass front clip by Johnson Manuf.
0 comments

Lucky to find some Tony Nancy Patches to sew into upholstery for the Super Stude.
0 comments

Ernie's Original Engine back in the day. Tony Nancy was a big part of putting this car and engine together..
0 comments

Starting New late model build. Milodon JP-1 alumn. block. BME rods, Arias Piston's.
0 comments

Keith Black Heads
0 comments

Weind front cover for cam pump.
0 comments

Fresh Keith Black Heads. Blower and tranny should be here soon.
0 comments

I built this Jig for the trunk hindges for the Super Stude.
0 comments

My buddy Joe Cox built this glass trunk lid for me. as someone stole the trunks lid and hindges. Great job Joe.
0 comments

Original hindges on the jig I made.
0 comments

Forming a piece of angle iron after making some cuts on the band saw.
0 comments

Used a piece of quarter square stock to form alone the outside for support.
0 comments

Finished product. Bought a 42 Studebaker Coupe just for a trunk to make a mold . I tried for two years to find a trunk lid.
0 comments

A little blocking and a done deal.
0 comments





RacingJunk.com
106 Main Street, North Adams, MA 01247
Toll Free: 866.326.9227 • Tel: 413.663.3496 • Fax: 413.663.3615 • Email: support@racingjunk.com

Execution Stats: 0.804 sec / 5.4 MB used / 5.5 MB peak