JUST OFF THE DYNO

HERE ARE SOME VIDS

http://www.youtube.com/watch?v=VFYhWspPP9c DYNO RUN

http://www.youtube.com/watch?v=Fd0jeHzOQes DYNO NUMBERS

THIS IS A NITROUS COMBO IT WOULD MAKE 900 + IF YOU CHANGED THE CAM AND FUEL

THERE IS NO JUNK HERE ALL THE BEST PARTS

Brand New Only 6 Dyno Runs Dart Iron Eagle / Rocket Block
9.325 Deck .391 Raised Cam 4.125 Bore
Lifter Trued For .904 Lifters

Lunati Pro Series Crank 4" Stroke 350 Main 2.100 Rod STD / STD

GRP 1200 Series 6" Rods With less than 20 Runs 2.100 .927

Brand New Custom JE Nitrous Pistons Gas Ported .43 1/16 3/16 Only 6 Dyno
Runs

The Engine Is 14.5 TO 1

Brand new Hellfire Rings .43 1/16 3/16 Only 6 Dyno Runs

New Clevite V Series Rod and Main Bearings Only 6 Dyno Runs

Custom SBC LSM Camshaft for Nitrous 4 / 7 Swap .840 / 289 Intake .821 /
305 Exhaust

Comp Cams SBC Rocket Block Raised Cam Belt drive

Billet Moroso Oil pump NEW With ARP Shaft Only 6 Dyno Runs

Billet Fabrication 2 Piece Custom Full Sump Oil Pan For SBC Rocket Block

Brand new DJ Safety SFI Engine Diper NEVER RAN

14 Degree Pro Action Heads

2.180 Titainum Intake Valves

1.625 Titainum Exhaust Valves

Manley Nextek 221448-16 Springs Set up at 350@2.100

Manley Titainum Retainers lightweight Impinged.

Jesel Rockers 1.85 Intake and 1.80 Exhaust.

Manley 3/8 Pushrods 9.050 and 9.000

Crane Ultra Pro .904 Lifters 210" offset intake pushrod seat Part #
11575-16 "NEW" Only 6 Dyno Runs

Heads Flow 375CFM on the Intake and 270 on the Exhaust 290CFM With a
Pipe On a Superflow SF600 FlowBench Heads Have A 39cc Chamber

ARP "NEW" Head Studs Only 6 Dyno Runs

Gregg Davis Custom Sheetmetal Intake set up for 2 foggers Can be used on
std Deck or tall Deck block

2 Holley HP Dominator Done by Performance Carburetors Stage 2
With Linkage

Carbon Fiber Valve Covers

Spare sets of SCE Intake Gaskets

New Fel-Pro MLS Head Gaskets 1144-061 Only 6 Dyno Runs

MSD Front mount disributor For SBC Part # 8730

MSD Crank Trigger 6" SBC

Powerbond 6 1/4 Race Balancer

CSI SBC Water pump

Moroso Mandrel

Moroso 3 Vane Vacuum Pump

Motor plate For SBC

Moroso Ultra 70 Wires "NEW" Only 6 Dyno Runs

MSD Billet Oil Plug

Two Edelbrock Foggers E2 NOZZELS

Custom Step Headers For SBC Coated 2 1/8 to 2 1/4 With Edelbrock 4"
Merge Collectors S/S Fits 68/72 Nova / 67/69 Camaro With 18 or 14 Degree
Heads Must have Rack And Pinion

Motor ran a 7.62 @ 2820lbs in a 10.5 Outlaw Truck on one Stage .38 Jets
And 8.08 @ 2980lbs In a Drag Radial Car One stage .38 Jets .

$14500.00 OBO

Seller Phone Number: (805) 583-0602

This item is NEW

Trades NOT ACCEPTED

Payment options:

Item Location: SIMI VALLEY, CA Get Directions To This City

This ad expires in 38 days.