Welcome to RacingJunk Classifieds, The World's #1 Motorsports Marketplace

For Sale: 1963 PBRC Corvette - Sonny's 818 N/A HEMI


Ad #182228376   Posted:2014-06-26 02:55:51

This ad expires in 0 days.


Just ran 4.33 @ 163 at YB with more left. All Motor!
Above Added: Tue September 2, 2014, 7:13 am EST
Reposting due to so called "buyer" backing out of deal. No more BS please - Call me only if you have the money. May be interested in possible trades but must only be quality name cars Bickel, Haas, TM,etc.
Above Added: Sat August 16, 2014, 4:01 am EST
No time to race and not enough support so its time to sell as I am tired of looking at it just sit. Maybe find something of lesser value and race it!

1963 Pat Bennett built completed April 2013-Serial # MC 553
26 passes on car since new and 10 on motor since last freshen up. Hands down one of the nicest and detailed cars in the country with no expense spared! Built to run top sportsman but has 20 lb fire system, 15:3 spec wheels, driver side carbon fiber on door X as required for Pro Mod. Change brakes to carbon fiber and you can run Pro Mod with this car.

BODY/CHASSIS
-Hairy Glass Pro Mod body with 45" overhang
-Jerry Bickel 547C hoodscoop
-Incredible paint and airbrushing by Bruce Mullins
-113" wheelbase double frame rail 6.0 25.1E cert till 5/16
-PBRC 4130 Pro Mod floater housing nickel plated
-Mark Williams 40 spline gun drilled axels and brakes
-Mark Williams pro mod center section with 4:10 gear
-PBRC wishbone
-PBRC extreme duty four link
-Mark Williams anti roll
-Strange Ultra struts and steel brakes
-Koni dbl adj shocks
-4130 CM driveshaft enclosure
-Rear 2 piece driveshaft enclosure
-96" C/M double wheelie bar
-88" C/M single wheelie bar
-Dual Stroud spring launcher chutes
-Interior battery disconnect by Lokar Products
-16 x 16 Weld ultra lite bead locks with top fuel centers 15:3 spec pro mod legal
-Weld V-series spindle mount front wheels
-Flaming River rack & pinion
-PBRC steering column with APEX joints
-Roller bearing pedals ( Has clutch pedal installed to run manual trans)
-Polished aluminum front and mid motor plates. Have spare front plate for wedge motor
-Strange master cylinder
-All brake lines and fire system lines and clamps are stainless steel. Brake lines are run through the chassis.
-Complete interior is carbon fiber
-Firewall and drivers floor is steel
-Removable dual NOS bottle mounts and tabs for handle valves
-Dual starter bump buttons on firewall
-Removable rear window lexan (dzused on)
-Stroud belts
-ISP head surround
-Working 63' Vette tail lights
-Removable tool tray - Mounted to radiator
-Rear push bar mount for golf cart
-Jerry Bickel double pass radiator with remote Miezere water
pump
-Chrome plated four link bars, wishbone, anti roll links, parachute mounts, double wheelie bar, tie rods, control arms, steering shaft, pedals, fuel cell mount, isolator tray mount, shifter, delay box mounts, and dzus fasteners
-All certs. are current

ENGINE/TRANSMISSION
-Sonny's 818 HEMI naturally aspirated 1800 HP and 1303 torque on Sonny's Dyno. See Dyno sheet in pictures
-Dart Billet block 12.00 deck height with 1.00" raised cam
-70 mm camshaft
-GRP rods
-BME pistons
-Moroso pan
-Moroso 4 stage dry sump system
-Star pro mod vacuum pump
-Jesel front belt drive
-ATI balancer
-Sonny's hemi heads with T&D rockers, PSI valve springs, and Manley titanium valves
-Sonny Bryant 5.650 billet crankshaft
-Sonny's sheetmetal intake
-CFM split dominators - Dale Cubic Performance Carbs
-Sonnys HEMI valve covers with billet rail
-Brand new Moroso HEMI plug wires
-Brand new XRP pro plus crimped lines on entire motor
-Have headers for 5.0 bore space hemi and 5.0 bore space wedge motor. Both SS with O2 and EGT bungs
-Rossler terminator 6 glide with 4 passes since freshened
-Turbo 400 ringless input shaft
-10.5" bolt together convertor
-CSR billet flywheel with removable ring gear
-4" aluminum driveshaft from PST with Mark Williams billet yoke
-Precision shifter

ELECTRONICS/IGNITION

-MSD power grid
-Racepak smartwire with overhead switchpanel. This thing does it all!
-Racepak V300SD and UDX dash with the following sensors
-oil pressure, oil temp, water temp, fuel pressure, trans temp, vacuum, O2 two channel, 8 EGT's, driveshaft speed, and G meter.
-16 volt turbo start AGM battery and charger
-Professionally wired and very, very neat

I may be missing some small items but this is the bulk of it. This is one awesome car that just plain works. Made one pass with this combo and went 6.88 @ 206.10 on a very moderate pass. Car will go high 6.50's or low 6.60s in good air. Qualify at the top at any race. This car is like new, meticulously maintained, and cleaned after every outing.

TURN KEY - 128,000
ROLLING - 82,000 without engine, trans, and converter

Car will come with projacks, chassis stabilizer, spare starter and all software at turnkey price.
I will not respond to emails through racing junk so please call me if you are SERIOUS and have the money. I will be more than happy to answer any questions you have and send any pictures you want.





Seller Phone Number: 203-414-7305
This item is USED
Trades NOT ACCEPTED
Payment options:
Item Location: EASTON, CT Get Directions To This City
Contact Seller
This ad expires in 0 days.
From:    To: 
profile picture Seller Information

Ad posted by:
TS1369 (#18781)
Member Since: 2003-08-06

Phone Number: 203-414-7305

Member Feedback
Number of Honor Payments: 1
Average Accepted Sale Price: $0.00
Average Honor Payment: $30.00

Gold Seller
Contact Seller
Facebook
Twitter
Print Ad
More
Enter Friend’s Email:

DID YOU BUY THIS ITEM?
Report the sale - click here



RacingJunk.com
106 Main Street, North Adams, MA 01247
Toll Free: 866.326.9227 • Tel: 413.663.3496 • Fax: 413.663.3615 • Email: support@racingjunk.com

Execution Stats: 0.364 sec / 16.0 MB used / 16.1 MB peak