Welcome to RacingJunk Classifieds, The World's #1 Motorsports Marketplace


Ad #182112032   Posted:2014-02-11 12:25:34

This ad has been marked as sold.

Dynojet 250i and Industrial Noise Control (INC) soundproof room with a ventilation system. Dyno is in perfect working order. In addition to the Dyno, upgrades that were added at the time of purchase include: Air fuel ratio module, dual multi-axis cooling fan system, monitor tray, eddy current load absorption unit and power clamp/carriage. Dyno does not include a ramp.

Please call 302-740-6900 to schedule a time to try it out. These are large items that are very heavy. You will have to have a good size truck to transport this -- a pickup truck will not do. You are also responsible for disassembly of the soundproof room. I may consider splitting the pair for the right price. The sale does not include the computer, monitor, printer, toolbox, table and any other personal items seen in the picture. Local pick up only.

Below is the information on the Dyno from the Dynojet website.

The Dynojet Load Control System was developed through years of experience with over 3,900 dynomometer installations worldwide. The design is easy to operate and provides the function of steady sate load control. Dynojet's Load Control System uses the latest in eddy current power absorption technology, which combines with easy to use software, so any technician can get repeatable, consistent results.

Closed-loop control of Speed or RPM
Easy-to-use software, push button operation
Test Vehicles at full or partial throttle
Absorption unit capable of 858 lb/ft torque
Compact design
Ignition Wire Inductive Tachometer Pickup Leads
Remote Software and Brake Control From Driver's Seat
Inertia Dynamometer Chassis with standard wheel base up to 84 inches
Measures up to 750 horsepower
Primary Wire Inductive tachometer pickup
Secondary Inductive Pickups (spark plug clamps connect directly to spark plug wires)
WinPEP7 Software
Bike Starter System
Wheel Lock

Dynoware EX+ hardware includes:

: CPU Module: Com Port Interface, runs on 12VDC & 110VAC
: Dyno Module: Sends and receives data to and from the Dyno
: Atmosperic Sensing Module: Automatically measures absolute pressure, air temperature and relative humidity
: RPM Module: Receives and processes ignition (spark) signals for correct engine speed measurement


Base Length 79.83"

Base Width 29.83" (202.8 cm)

Base Height 18.10" (45.9 cm)

Drum Diameter 18" (45.72 cm) per wheel

Drum Width 16.37" (41.59 cm)

Drum Concentricity +/- 0.001" (+/-0.025 mm)

Maximum Length (Front of Front Wheel to Center of Rear Wheel) 84" (213.4 cm)


Dynamometer 2375 lbs (1077 Kg) (approx.)


Drum A 106 Steel

Shaft 2 3/16 inch 1144 turned ground & polished steel

Frame 10 Gauge Cold Roll Steel


Modeled Mass (Standard) 450 lbs (204 Kg) (approx.)

Modeled Mass (High-Inertia) 650 lbs (295 Kg) (approx.)

Maximum Horsepower 750 hp

Maximum Speed 200 mph

Maximum Torque 750 ft/lbs

Temperature Range 32 o F to 158 o (0 o C to 70 o C)


Calibration Not Required (Factory Calibrated)

Inductive Pickup Primary Wire RPM Pickup

Power Requirement 240v 30amp
single phase circuit

Remote Switches

Remote Software Control


Timing Accuracy +/-1 microsecond

Drum Speed Accuracy +/- 1/100th MPH

RPM Accuracy +/- 1/10th RPM

Seller Phone Number: 3027406900
This item is USED
Payment options:
Item Location: WILMINGTON, DE Get Directions To This City
Contact Seller
This ad has been marked as sold.
From:    To: 
Seller Information

Ad posted by:
bikerbargains (#685085)
Member Since: 2013-06-15

Phone Number: 3027406900

Member Feedback
Number of Honor Payments: 0
Average Accepted Sale Price: $0.00
Average Honor Payment: $0.00

Contact Seller
Print Ad
Enter Friend’s Email:
  • Member has no other classified ads.

Report the sale - click here

106 Main Street, North Adams, MA 01247
Toll Free: 866.326.9227 • Tel: 413.663.3496 • Fax: 413.663.3615 • Email: support@racingjunk.com

Execution Stats: 0.217 sec / 15.9 MB used / 16.0 MB peak