Welcome to RacingJunk Classifieds, The World's #1 Motorsports Marketplace

For Sale: Sbc Small Block Chevy 210 Aluminum Heads Kit

Ad #181768791   Posted:2014-07-20 08:46:18
This ad expired 2 days ago.
$999.95


This Kit Includes:

Small Block Chevy Stainless Roller Rockers 1.5 3/8, Small Block Chevy 7.900 Push Rods Chromemoly, Aluminum Heads, Small Block Chevy Aluminum Head Gaskets Bolts Washers , Small Block Chevy Aluminum Intake

Aluminum Heads:

This is A Complete Set (Price IS For 2 Cylinder Heads)Straight Plug For Small Block chevy 210CC intake Runners And 64CC Combustion Cambers There Heads Are Ready To Bolt On with 3/8 Studs And Guide Plate The Springs are Good up to 600 Lift Solid Or hydraulic Roller Cams
Aluminum Cylinder Heads Feature-

Hardened Seats
Bronze Valve Guides
High Grade Aluminum
Multi-Angle Seat Design
Available Complete or Bare
Available fully CNC Machined
Designed Performance Valve Springs
Advanced Port Design for Greater Flow
Combustion Chamber: 64cc
Intake Runner: 210cc
Intake Valve: 2.02"
Exhaust Valve: 1.60"
Spring Pressure Closed: 140 lbs. @ 1.800"
Spring Pressure Open: 325 lbs. @ 1.225"
Retainer Material: Steel
Valve Seal Material: Viton
Valve Guide Material: Manganese Bronze
Valve Job: 3-angle

Stainless Roller Rockers:

This is a set of 16 stainless steel SBC Chevy 1.5 ratio roller rockers with a 3/8ths stud and 16 poly locks.

Pictured above, these roller rockers are brand new fresh out of the packaging.

After selling every brand of rocker we have imported our own to meet our tough standards. These stainless steel rockers are really a top of the line product and offer many benefits over aluminum roller rockers.

You will notice:

· They allow for an overall higher load capacity

· Our stainless steel roller rockers can handle 750+ pounds of spring pressure

· Our stainless steel roller rockers can withstand engines turning at 8000 RPM

· These roller rockers are also lighter on the roller tip than aluminum

These are the roller rockers for you if you need a product that will hold up to the demands of daily driving and running hard. This is a truly well made set of roller rockers that you definitely won’t worry about the end pin coming out.

You will also notice:

· These will provide an increase in horse power of 10-15

· You will experience an extended life of valve train

· You will feel more receptive acceleration

· You will experience an increase in fuel efficiency

· Your oil temperature will run cooler

PushRods:This Is For A Brand New Set of chromemoly 5/16" 7.900 Length Pushrods and are .080 thick They Are .100 Longer then Factory. I could go on For Days Saying These Are "Superior To others On Ebay", But in All Reality These Are The Same Ones Every One Else Is Selling, Not Just a Gimmick Label I Add to Charge More

Gasket Kit:

BRAND NEW SBC Felpro Gasket Kit.

This Kit Is A must When Running Pro Comp Heads OR Any Aftermarket Aluminum Heads

The kit includes the following:

ü 2 (two) FELPRO Head Gaskets that feature a Perma-Torque/Blue Gasket body with a solid-steel core to minimize torque loss and gasket blowout. They also have a wire-ring combustion seat with stainless steel armor for extra sealing force around combustion chambers.
Gasket Bore: 4.166
Comp Thickness: .041
Comp Volume: 9.1cc

ü 2 (two) FELPRO Performance 1255 Intake gaskets designed for Vortec cylinder heads. Installation is simple with a bead of silicone at the manifold ends.
Port Height: 2.1”
Port Width: 1.08”
Thickness: .120”

ü Small Block Chevy Cylinder Head Bolt Kit With Washer that fits most new & aftermarket aluminum

Dual Plain Intake:

This is for a BRAND NEW aluminum dual plane intake for Small Block Chevys with 1996 and up Vortec Heads.

There is no provision for manual choke or exhaust crossover, and are not EGR equipped.

This intake is ideal for everyday to high performance street applications. These intakes are produced from steel molds to reduce core shift.

This intake manifold is for use with square bore style carbs, and has an intake port dimension of 2.06”x1.18”. The manifolds height is 4.65”.

Features:

· 180° dual plane high rise design for power from 1500 to 6500 RPM

· Bosses on intake runners can be drilled and tapped for nitrous

· Air Gap under plenum for cooler fuel charge

· Square bore flange for the Holley 4150/4160 carburetor

· Perfect port position - allows customer to customize porting for maximum power

· Four corner water outlets

· All intakes are pressure tested in house to ensure a leak free manifold

· Recommended intake gasket Felpro 1255

· Recommended torque is 15-18lb

Business Phone Number: 7064789560
This item is NEW
Trades NOT ACCEPTED Payment options:
Item Location: COLUMBUS, GA Get Directions To This City
Contact Business
This ad expired 2 days ago.
From:    To: 



RacingJunk.com
106 Main Street, North Adams, MA 01247
Toll Free: 866.326.9227 • Tel: 413.663.3496 • Fax: 413.663.3615 • Email: support@racingjunk.com

Execution Stats: 0.421 sec / 16.1 MB used / 16.2 MB peak