For Sale: 10,000 RPM Large Absorption/Water Break Engin
10,000 RPM is selling their Complete Engine Water Break / Dynomometer in Complete working order. This dyno was developed and manufactured by Ron Hammel of 10,000 RPM and Dale Armstrong and was used to test Nitro, Alcohol and gas engines of various sizes and horsepower ratings. Up to 8,000 HP Nitro Engines. Used by Bob Gilbertson's Terminator Racing Nitro Funny Car, Mike Stewart of Mike's Transmission, and the McGee Brothers Quad Cam Top Fuel Engines and many more. 10,000 RPM, Inc. of Lancaster, Cal. Manufactured Large Hydraulic Engine Dynamometers Power Absorption Units. The Dyno 11,000 features a Closed Loop System with
100% Repeat ability, with every pull. This Closed Loop System offers more consistent loads by
reusing the same load water that is then cooled by a heat exchanger. 10,000 RPM Inc. Dyno 11,000 is 24" OD with a 19.2" Steel Billet Rotor that is 6" wide, this
Dyno Absorption unit can absorb 100-6,000 + HP and is easily capable of holding back 11,000 + ft. lbs. of torque. The Dyno 11,000 water break style engine dynamometer has its
best torque holding capacity at 1,250 - 3,500 RPM. For setting up a Large Engine Dynamometer to run HI RPM / HI HP engines you need a dynamometer to run at 1/4 engine speed for Repeat Ability and LargeHorsepower Capacity. Otherwise when the engine is running at 9,000 RPM the dyno is only turning 2,250 RPM. It's always a good idea to have more Horsepower Capacity than you need in the dyno. Dyno's that run at engine speed have become obsolete for High RPM R&D. If you are boiling the water in your dyno you know what we mean. The
small engine dyno's on the market run at engine speed and this will make the water boil over the tips of the water wheel, or cavitate from Hi RPM. When running the Dyno/Water Wheel at Engine RPM you lose the accurate Repeatability and torque holding capacity. 10,000 RPM, Inc. Dyno 11,000 has been the Research and Development test facility for many High HP Nitromethane, Alcohol and Nitrous racing teams. 10,000 RPM, Inc. has tested many types of engines on our Dyno 11,000 that run at 1/4 Engine RPM.
Complete System includes:
8,000 plus HP Power Absorption Unit (Water Break Assembly)
24" Outside Diameter x 12.25" W, 19.2" Steel Billet Rotor, 5" Dia. Main Shaft
110 Volt Load and Unload Valves
2- Bearing Supports (Each support has 4 bolts with 4 large Sealed Ball Bearings)
Steel Billet Powder coated Stand.
4:1 Gear Box
Stand and controls for operating
All Framing and etc.
Hemi Hedders and various headers and adapters
We currently have in use 8 Header Thermo Couplers and 8 Seperate Exhaust Temp Gauges.
(As for Data Acquistion- We come had CEHCO but not sure of the status on it, hasn't been used in years)
Adapter/Engine Plate is drilled for a lot of applications.
24volt Diesel Stater w/ Large Ring Gear seperate from Flywheel Ring Gear, a lot of various flywheels for the dyno.
Misc Headers including Late Style Hemi Heads/426 Brad Heads, with a stand/adapter to adapt long tubes to exit building.
Complete Ready to Run!!!
MUST SELL!!!!!!!!!!!! MAKE A REASONABLE OFFER
SHIPPING WORLDWIDE BUT NOT FREE OR INCLUDED
AS FOR SHIPPING ONCE FULL PAYMENT IS RECEIVED WE COULD PALLETIZE THE ITEMS FOR SHIPPING AT BUYERS EXPENSE!!!!!!
SHIPPING CAN BE WORLDWIDE / INTERNATIONAL AT BUYERS EXPENSE
Seller Phone Number2: (661) 816-8905
This item is USED
Trades NOT ACCEPTED
Instructions for buyer: WWW.10000RPM.COM
Ad posted by:
Member Since: 2006-03-07
Phone Number: 661-942-1312
Phone Number: (661) 816-8905
Number of Honor Payments: 0
Average Accepted Sale Price: $0.00
Average Honor Payment: $0.00
Report the sale - click here