Welcome to RacingJunk Classifieds, The World's #1 Motorsports Marketplace

For Sale: 1966 Mustang fastback tube chassis car


Ad #182211602   Posted:2014-05-31 07:43:53

This ad expired 74 days ago.
$25,000.00


Car is new with 8 passes on it. Mild steel chassis will certify to 8.50. Back half and cage by Gebhardt Pro Cars. Front half by JLRC. Both are tied together to make a full tube chassis, just done in two parts. Check out the link below for pictures of the build. 9" Ford 4 link rear, Strange strut front w/Pinto rack. All fiberglass except roof and rear quarter panels. Also, an extra new hood and scoop for the tunnel ram set up. Extra trunk lid. Paint on car isn't too bad, but the hoods, trunk lid, and scoops are in primer. All Lexan windows. 4 wheel disc brakes. 4.88 pro gears, 33 spline axles and spool, "N" case. New Toyo 14x32 slicks and Goodyear 25" fronts. Wheelie bars and Stroud chute. Front mounted fuel system with 3 gallon aluminum fuel cell. Two new batteries. Trans cooler w/fan. Belts are good till 7-2014. For medium height driver up to about 5'10".

Set up for Ford Cleveland and powerglide. Engine is currently out of car. Buyer has to build an engine from the parts that are included. Here is a partial list: 5 blocks, 2 are std. bore, 3 are .030" over. 2 of the bored blocks are 4 bolt main. One of those and another 2 bolt main have a sleeve. There are 5 cranks. 3 are turned and 2 probably need it. None more than .010". A couple sets of Eagle H beam rods and 5 used spares, one set is new in box. One used set of worked over stock rods with KB hyper pistons. One set new Arias pistons. 13 used TRW pistons. All pistons are domed and .030" over. New 1980's stroker kit with Venolia pistons and aluminum rods. The offset ground crank with that is rusty (ruined). 4 sets of closed chamber 4V heads, all stock ports. 3 sets of aluminum port plates to make the heads into hi-port exhaust (like early pro stock heads were done). Tunnel ram 2x4 intake with new 750 carbs (never run) and all required plumbing, Holley Strip Dominator intake, new FunnelWeb intake, Holley 950HP carb. 3 distributors, one for crank trigger. Many different cams, all new, solid lifter flat tappet, and solid rollers with lifters. And a whole lot of other Cleveland parts like valve covers, oil pans, oil pumps, front covers, windage tray, headers, water pumps, flex plates, gaskets, front balancers, accusump, etc. I will compile a detailed list if anyone shows any real interest.

4 aluminum case powerglides, all 1.76 first gear. Good one in car has pro brake. One completely stock and 2 racing ones with trans brakes will need rebuilding, one rebuild kit included. There's various other trans parts. New PTC 8" converter approximately 4,500 stall. I do not know the exact weight of the car. No trades. Will not sell as a roller, buyer must take everything. Price is firm.

For lots of pictures go to: http://www.midrivers.com/~hotrod/drag.html

Please email any questions.

Seller Phone Number: This user has not entered a phone number yet.
Send message to seller below.
This item is USED
Trades NOT ACCEPTED
Payment options:
Item Location: CIRCLE, MT Get Directions To This City
Contact Seller
This ad expired 74 days ago.
From:    To: 
profile picture Seller Information

Ad posted by:
speedcrazy (#10184)
Member Since: 2003-04-19

Member Feedback
Number of Honor Payments: 0
Average Accepted Sale Price: $0.00
Average Honor Payment: $0.00

Contact Seller
Facebook
Twitter
Print Ad
More
Enter Friend’s Email:
  • Member has no other classified ads.

DID YOU BUY THIS ITEM?
Report the sale - click here



RacingJunk.com
106 Main Street, North Adams, MA 01247
Toll Free: 866.326.9227 • Tel: 413.663.3496 • Fax: 413.663.3615 • Email: support@racingjunk.com

Execution Stats: 0.439 sec / 16.0 MB used / 16.1 MB peak